EE-SPY415 Omron, EE-SPY415 Datasheet

Page 1

... Note: 1. When ordering, add the rated coil voltage to the model number(s), followed by “(S)”. Rated coil voltages are given in the coil ratings table. Example: MY2 AC12(S) ↑ Rated coil voltage 2. Arc barrier standard on all four-pole relays. 3. Other models also available, such as, three-pole versions, flangemount, PCB, etc. Contact your Omron Representative for details. Model Plug-in socket/solder terminals Standard with LED With LED indicator and ...

Page 2

... Performance characteristic data are measured at a coil temperature of 23° coil resistance and impedance are provided as reference values (at 60 Hz). 4. Power consumption drop was measured for the above data. When driving transistors, check leakage current and connect a bleeder re- sistor if required. 5. Rated voltage denoted by “*” will be manufactured upon request. Ask your OMRON representative. ...

Page 3

... MΩ min. (at 500 VDC) 2,000 VAC, 50/60 Hz for 1.0 min (1,000 VAC between contacts of same polarity) Destruction: Hz, 1.0 mm double amplitude Malfunction: Hz, 1.0 mm double amplitude 2 Destruction:1,000 m/s (approx. 100G) ...

Page 4

... Engineering Data ■ Maximum Switching Power MY2 AC resistive load AC inductive load (cosφ=0.4) DC resistive load DC inductive load (L/R=7 ms) Switching voltage (V) ■ Endurance MY2 (Resistive Loads) 10000 5000 3000 250 VAC 1000 30 VDC 500 30 VDC 300 250 VAC 100 Switching current (A) ...

Page 5

MY4Z (Resistive Loads) 10000 5000 3000 1000 250 VAC 500 300 30 VDC 100 30 VDC 50 250 VAC 30 10 Switching Current (A) MY4Z (Inductive Loads) 10000 5000 3000 1000 30 VDC 500 300 30 VDC 100 250 VAC ...

Page 6

... Eight, 1.2 dia. × 2.2 long holes 0.5 28 max. 36 max. 6.4 21.5 max. 2.6 Eight, 1.2 dia. × 2.2 long holes 8 36 max. 14.2 2.6 Fourteen, 1.2 dia. × 2.2 long holes 8 14.2 36 max. <1.417> 6 max. 21.5 max. 28 max. 21.5 max. ...

Page 7

Terminal Arrangement/Internal Connections (Bottom View) MY2 MY2N/MY2IN (AC Models) MY2N-CR/MY2IN-CR (AC Models Only) MY4(Z) MY4(Z)N/MY4(Z)IN (AC Models) MY4(Z)N-CR/MY4(Z)IN-CR (AC Models Only) MY2N/MY2IN MY2N-D2/MY2IN-D2 (DC Models) (DC Models Only) MY2N1/MY2IN1 MY2N1-D2/MY2IN1-D2 (DC Models Only) (DC Models Only) MY4(Z)N/MY4(Z)IN MY4(Z)N-D/MY4(Z)IN-D2 (DC ...

Page 8

... The values for insulation resistance were measured at 500 V at the same place as the dielectric strength. 3. The maximum operating ambient temperature for the PYF08A-N and PYF14A-N is 55°C. 4. When using the PYF08A-N or PYF14A operating ambient temperature exceeding 40°C, reduce the current to 60%. 5. The MY2(S) can be used at 70°C with a carry current ...

Page 9

Mounting Plates for Sockets Socket model For 1 socket PY08, PY14 PYP-1 Note: PYP-18 and PYP-36 can be cut into any desired length in accordance with the number of Sockets. ■ DIN Rail Track and Accessories Description Mounting rail ...

Page 10

... Note: The PY08-Y1 includes sections indicated by dotted lines. PY08-02 16.5 max. 268 General-purpose Relay Terminal arrangement/ internal connections (top view) 31 max. Fourteen sems screws 31 max. Eight 1.2 elliptical holes 25.5 max. 29.5 max. 20 max. 24 max. 25.5 max. 29.5 max. 22 max. ...

Page 11

... max max max Fourteen 1.2 elliptical holes 25.5 max. 29.5 max. 24 max. 20 max. 25.5 max. 29.5 max. 22 max. Mounting holes 3.0 dia. 3.5 dia 18.7 9 Note: Track mounting is also 11 possible. Refer to page 12 for supporting tracks. Two, 4.5 dia ...

Page 12

... PYDM-14SB PYDM-08SR 19.7±0.3 PYDM-08SB Note: 1. The relationship between the model number, the length L, and the color of the insulating coating is shown above. 2. The insulating coating must be able to withstand a voltage of 1,500 V for 1 minute. Use either the material of the insulating coating. ...

Page 13

Clip and Release Levers PYCM-14S PYF14S Lever 26.5 typ. 21.5 typ. ■ Hold-down Clips PYC-A1 PYC-A1 (2 pcs per set) (2 pcs per set) 36.3 4.5 1.2 4.5 PYC-P PYC max. 3.3 38.5 PYCM-08S PYF08S Lever 28 ...

Page 14

Mounting Plates for Back-connecting Sockets PYP-1 PYP-1 Two, 3.4-dia. holes t=1.6 PYP-18 PYP-18 72 elliptical holes ■ Mounting Track and Accessories DIN Rail Track PFP-50N/PFP-100N Note: The figure in the parentheses is for PFP-50N. PFP-100N2 End Plate PFP-M 272 ...

Page 15

Spacer PFP-S ■ Approved Standards VDE Recognitions (File No. 112467UG, IEC 255, VDE 0435) No. of poles Coil ratings 2 6, 12, 24, 48/50, 100/110 110/120, 200/220, 220/240 VAC 4 6, 12, 24, 48, 100/110, 125 VDC UL Recognized (File ...

Page 16

... AWG24 to AWG16 Applicable Wire Type Solid wires, stranded wires, flexible wires, or wires with ferules can be used. 2.2 ≤ Diameter D (mm) ≤ 3.2 (3.5: see note 2.) < (See note 1.) Conductor diameter d (mm) or length of sides a and b (mm) ≤ 1.9 Wires with Ferules ...

Page 17

... Wire connection holes Release holes Fig. 2 Wire Connection Holes and Release Holes Wire connection hole Release hole Screwdriver Fig. 3 Section A-A of Fig. 2 See note 1, above. Recommended wire sizes See note 2, above. 0.5, 0.75 1.0 mm 0.5, 0.75 mm 0.5, 0.75, 1.0, 1 ...

Page 18

... General Precautions • Use the clip to prevent relays floating or falling out of the socket. • Do not use the product if it has been dropped on the ground. Drop- ping the product may adversely affect performance. • Confirm that the socket is securely attached to the mounting track before wiring ...

Page 19

... II. SALES 1. Prices; Payment: All prices stated are current, subject to change without notice by Seller. Buyer agrees to pay the price in effect at the time the purchase order is accepted by Seller. Payments for Products received are due net 30 days unless otherwise stated in the invoice. Buyer shall have no right to set off any amounts against the amount owing in respect of this invoice ...

Page 20

... Please consult with your Seller representative at any time to confirm actual specifications of purchased Product. 5. Errors and Omissions. The information in this publication has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors, or omissions. ...