DLP2232ML-G DLP Design Inc, DLP2232ML-G Datasheet

DLP2232ML-G

Manufacturer Part Number

DLP2232ML-G

Description

Interface Modules & Development Tools Low Profile 2232M

Manufacturer

DLP Design Inc

Datasheet

1.DLP-2232ML-G.pdf (5 pages)

Specifications of DLP2232ML-G

Interface Type

UART

Product

Interface Modules

For Use With/related Products

FT2232D

Lead Free Status / RoHS Status

Lead free / RoHS Compliant

Current page: 1 of 5
Download datasheet (153Kb)

DLP-2232ML-G LOW-PROFILE USB MODULE

* Lead Free *

1.0 Introduction

The DLP-2232ML-G utilizes FTDI's third-generation USB UART/FIFO I.C., the

FT2232D. This low-cost, RoHS compliant development tool features two Multi-Purpose

UART/FIFO controllers that can be configured individually in several different modes.

In addition to the UART interface, FIFO interface, and Bit-Bang IO modes of the

second-generation FT232BM and FT245BM devices, the FT2232D offers a variety of

additional modes of operation including a Multi-Protocol Synchronous Serial Engine

interface designed specifically for synchronous serial protocols such as JTAG and SPI

bus.

The DLP-2232ML-G features a quality four-layer printed circuit board with a solid

ground plane, an integral 93C56 EEPROM on board for easy OEM customization and a

standard 40-pin, 0.6in wide footprint. Integral power control and on-board MOSFET

power switch make the DLP-2232ML-G a perfect choice for USB bus-powered, high-

power designs as well as self- and low-powered products.

NOTE: With the exception of the mechanical connectors, mechanical dimensions and the

host connection interface signals, the DLP-2232ML-G and DLP-2232M-G are the same

product. The supporting electronics for the USB connector are already on the DLP-

2232ML-G board, just add a type B connector to your design and you’re ready to go.

For a complete list of features and specifications please refer to the datasheet for the

DLP-2232M-G.

Rev 2.1 (July 2008)

DLP-2232ML-G DLP Design, Inc.

Related parts for DLP2232ML-G

DLP2232ML-G Summary of contents

Page 1

Introduction The DLP-2232ML-G utilizes FTDI's third-generation USB UART/FIFO I.C., the FT2232D. This low-cost, RoHS compliant development tool features two Multi-Purpose UART/FIFO controllers that can be configured individually in several different modes. In addition to the UART interface, FIFO interface, ...

Page 2

Module Pin-Out Figure 2. Pin-Out (40 Pin DIP Header ) 2.1 Pin Definitions Since the DLP-2232ML-G does not have a USB connector, the USBDM and USBDP signal lines are brought out on pins 23 and 22 as shown here. ...

Page 3

Mechanical Dimensions 0.05 typ. ( 1.3typ.) 2.0 typ. (50.8 typ.) 0.05 typ. (1.3 typ.) 0.063 typ. (1.6 typ.) **Components on top and bottom of PCB Rev 2.1 (July 2008) Inches (mm) 0.1 typ. (2.54 typ.) .040” ID – Compatible ...

Page 4

Disclaimer © DLP Design, Inc., 2002 / 2008 Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced in any material or electronic form without the ...

Page 5

AGND 9 GND 18 GND 25 GND 34 GND AVCC 3 VCC 42 VCC 14 VCCIOA 31 VCCIOB ...

Related keywords

DLP2232ML-G datasheet
DLP2232ML-G data sheet
DLP2232ML-G pdf datasheet
DLP2232ML-G component
DLP2232ML-G part
DLP2232ML-G distributor
DLP2232ML-G RoHS
DLP2232ML-G datasheet download