BLM18AG471SH1D Murata, BLM18AG471SH1D Datasheet - Page 62

• Manufacturer Part Number: BLM18AG471SH1D
• Description: EMI/RFI Suppressors & Ferrites 0603 470ohms Gen Use Tape
• Manufacturer: Murata
• Series: BLM Ar

Specifications of BLM18AG471SH1D

• Shielding: Unshielded
• Test Frequency: 100 MHz
• Product: Chip Ferrite Beads
• Impedance: 470 Ohms
• Tolerance: 25 %
• Maximum Dc Current: 200 mAmps
• Maximum Dc Resistance: 0.5 Ohms
• Operating Temperature Range: - 55 C to + 125 C
• Package / Case: 0603 (1608 metric)
• Termination Style: SMD/SMT
• Frequency Range: 30MHz To 100MHz
• Dc Resistance Max: 0.35ohm
• Dc Current Rating: 500mA
• Ferrite Mounting: SMD
• Ferrite Case Style: 0603 / 1608
• Operating Temperature Min: -55°C
• Rohs Compliant: Yes
• Operating Temperature Max: +125°C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

4
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
c
<Unless otherwise specified>
c
1. Electrical Performance
60
No.
BNX024H/025H series Specifications and Test Methods
1
2
3
4
5
6
Temperature: Ordinary Temp. 15 to 35 C
Humidity: Ordinary Humidity 25 to 85% (RH)
Test and Measurement Conditions
Specifications
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Insulation Resistance
Dielectric Strength
DC Resistance
Capacitance
Insertion Loss
Voltage Drop
Item
BNX024H01: 100M min.
BNX025H01: 50M min.
Filter should not fail.
0.43 0.20m
BNX024H01: 4.7 F 15%
BNX025H01: 10 F 15%
BNX024H01: 35dB min. (100kHz to 1GHz)
BNX025H01: 35dB min. (50kHz to 1GHz)
45mV max.
Specifications
<In case of doubt>
Temperature: 20 C 2 C
Humidity: 60 to 70% (RH)
Atmospheric pressure: 86 to 106kPa
Specifications and Test Methods
Measured at DC rated voltage between terminal (1)(2) and
(3)(4).
Time: 60s max.
Charging Current: 50mA max.
Measuring Equipment: R8340A or the equivalent
Withstanding voltage shall be applied between terminal (1)(2)
and (3)(4).
Test Voltage: BNX024H01 125V (DC)
Time: 5 1s
Charging current: 50mA max.
Measured by the way of 4 terminal method between (1) and (2)
and between (3) and (4).
Measured by the follwing condition between Terminal (1)(2)
and (3)(4).
Frequency: 1 0.1kHz
Voltage: 1V (rms) max.
Measuring Equipment: HP4278A or the equivalent
Insertion Loss = -20 log E
E
E
After soldering the part on the test substrate, measure the
voltage with passing the rated current as shown in the
schematic below.
Where the terminals of the part shall be connected as follows:
Referring to the terminal No. shown in item 5, connect terminal
No. (2) and (4) by soldering copper wire with diameter more
than 1mm / length less than 6mm.
Then connect terminal No. (1) as (i) and terminal No. (3) as (ii)
the measurement circuit as mentioned above.
The probe for measuring the voltage shall be touched on the
solder fillet of (1)(3).
0
1
: Level without FILTER (short)
: Level with FILTER
*Method of measurement based on MIL-STD-220
50
SG
Attenuator
10dB
50
BNX025H01 62.5V (DC)
Balun
Test Methods
A
1
/E
Specimen
0
1
3
V
(dB)
Continued on the following page.
2
4
Specimen
(ii)
(i)
Attenuator
10dB
50
50
E
C50E.pdf
1
08.8.28