STM32F103ZGT6 STMicroelectronics, STM32F103ZGT6 Datasheet - Page 40

• Manufacturer Part Number: STM32F103ZGT6
• Description: MCU ARM 32BIT 1MB FLASH 144LQFP
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F103ZGT6

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 72MHz
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART, USB
• Peripherals: DMA, Motor Control PWM, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 112
• Program Memory Size: 1MB (1M x 8)
• Program Memory Type: FLASH
• Ram Size: 96K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 21x12b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-LFQFP
• Processor Series: STM32F101xG
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Data Ram Size: 80 KB
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 36 MHz
• Number Of Programmable I/os: 112
• Number Of Timers: 15
• Operating Supply Voltage: 2 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Operating Temperature Range: - 40 C to + 105 C
• Processor To Be Evaluated: STM32F103ZG
• Supply Current (max): 28 mA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Electrical characteristics
5.2
40/120
Absolute maximum ratings
Stresses above the absolute maximum ratings listed in
Table 8: Current
damage to the device. These are stress ratings only and functional operation of the device
at these conditions is not implied. Exposure to maximum rating conditions for extended
periods may affect device reliability.
Table 7.
1. All main power (V
2. Positive injection is not possible on these I/Os. V
3. I
Table 8.
1. All main power (V
2. Negative injection disturbs the analog performance of the device. See note in
3. Positive injection is not possible on these I/Os. V
4. I
5. When several inputs are submitted to a current injection, the maximum I
|V
V
V
supply, in the permitted range.
never be exceeded. A negative injection is induced by V
cannot be respected, the injection current must be limited externally to the I
injection is induced by V
supply, in the permitted range.
characteristics.
never be exceeded. A negative injection is induced by V
cannot be respected, the injection current must be limited externally to the I
injection is induced by V
positive and negative injected currents (instantaneous values). These results are based on
characterization with I
Symbol
SSX
INJ(PIN)
I
INJ(PIN)
|V
ESD(HBM)
I
DD
INJ(PIN)
Symbol
V
INJ(PIN)
I
I
–V
VDD
DDx
VSS
I
IN
V
IO
SS
must never be exceeded. This is implicitly insured if V
must never be exceeded. This is implicitly insured if V
|
SS
(2)
|
Voltage characteristics
Current characteristics
External main supply voltage (including V
and V
Input voltage on five volt tolerant pin
Input voltage on any other pin
Variations between different V
Variations between all the different ground pins
Electrostatic discharge voltage (human body
model)
characteristics, and
Total current into V
Total current out of V
Output current sunk by any I/O and control pin
Output current source by any I/Os and control pin
Injected current on five volt tolerant pins
Injected current on any other pin
Total injected current (sum of all I/O and control pins)
DD
DD
, V
, V
DD
DDA
DDA
INJ(PIN)
)
IN
IN
(1)
>V
>V
) and ground (V
) and ground (V
DD
DD
maximum current injection on four I/O port pins of the device.
while a negative injection is induced by V
while a negative injection is induced by V
Doc ID 16554 Rev 2
Ratings
DD
SS
/V
Table 9: Thermal characteristics
SS
SS
DDA
ground lines (sink)
, V
, V
Ratings
SSA
SSA
(3)
power lines (source)
DD
IN
IN
maximum must always be respected. I
maximum must always be respected. I
) pins must always be connected to the external power
) pins must always be connected to the external power
power pins
(4)
(2)
IN
IN
<V
<V
SS
SS
DDA
(3)
IN
IN
.
.
maximum is respected. If V
maximum is respected. If V
(1)
Table 7: Voltage
see
Absolute maximum ratings
(electrical sensitivity)
STM32F103xF, STM32F103xG
(1)
V
V
INJ(PIN)
IN
IN
SS
SS
Section 5.3.12:
–0.3
<V
<V
INJ(PIN)
INJ(PIN)
Min
(5)
 0.3
0.3
Section 5.3.19: 12-bit ADC
SS
SS
is the absolute sum of the
.
may cause permanent
value. A positive
value. A positive
characteristics,
V
-5/+0
INJ(PIN)
INJ(PIN)
Max.
 25
± 25
DD
150
150
± 5
25
Max
IN
IN
4.0
4.0
50
50
+ 4.0
maximum
maximum
must
must
Unit
mA
Unit
mV
V