AD7416ARMZ Analog Devices Inc, AD7416ARMZ Datasheet - Page 8

• Manufacturer Part Number: AD7416ARMZ
• Description: IC SENSOR TEMP 10BIT 8-MSOP
• Manufacturer: Analog Devices Inc

Specifications of AD7416ARMZ

• Function: Temp Monitoring System (Sensor)
• Topology: ADC, Comparator, Register Bank
• Sensor Type: Internal
• Sensing Temperature: -40°C ~ 125°C
• Output Type: I²C™
• Output Alarm: No
• Output Fan: Yes
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 8-TSSOP, 8-MSOP (0.118", 3.00mm Width)
• Ic Output Type: Digital
• Sensing Accuracy Range: ± 2°C
• Supply Current: 1mA
• Supply Voltage Range: 2.7V To 5.5V
• Resolution (bits): 10bit
• Sensor Case Style: MSOP
• No. Of Pins: 8
• Msl: MSL 1 - Unlimited
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-AD7416/7/8EBZ - BOARD EVALUATION FOR AD7416/7/8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

AD7416/AD7417/AD7418
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
Table 4. AD7417 Pin Function Descriptions
Pin No.
1, 16
2
3
4
5
6
7 to 10
11
12
13
14
15
Mnemonic
NC
SDA
SCL
OTI
REF
GND
A
A2
A1
A0
V
CONVST
DD
IN1
IN
to A
IN4
Description
No Connection. Do not connect anything to this pin.
Digital I/O. Serial bus bidirectional data. Push-pull output.
Digital Input. Serial bus clock.
This pin is a logic output. The overtemperature indicator (OTI) is set if the result of a conversion on Channel 0
(temperature sensor) is greater than an 8-bit word in the T
serial read operation. Open-drain output.
Reference Input. An external 2.5 V reference can be connected to the AD7417 at this pin. To enable the on-chip
reference, the REF
reference shuts down.
Ground reference for track-and-hold, comparator and capacitor DAC, and digital circuitry.
Analog Input Channels. The AD7417 has four analog input channels. The input channels are single-ended with
respect to GND. The input channels can convert voltage signals in the range of 0 V to VREF. A channel is selected by
writing to the configuration register of the AD7417.
Digital Input. This is the highest programmable bit of the serial bus address.
Digital Input. This is the middle programmable bit of the serial bus address.
Digital Input. This is the lowest programmable bit of the serial bus address.
Positive Supply Voltage, 2.7 V to 5.5 V.
Logic Input Signal. Convert start signal. The rising edge of this signal fully powers up the part. The power-up time
for the part is 4 μs. If the CONVST pulse is greater than 4 μs, the falling edge of CONVST places the track-and-hold
mode into hold mode and initiates a conversion. If the pulse is less than 4 μs, an internal timer ensures that the
track-and-hold does not go into hold, and conversion is not initiated until the power-up time has elapsed. The
track-and-hold goes into track mode again at the end of conversion (see the
IN
pin should be tied to GND. If an external reference is connected to the AD7417, the internal
Figure 6. AD7417 Pin Configuration (SOIC/TSSOP)
REF
GND
SDA
A
A
SCL
OTI
NC
IN1
IN2
IN
1
2
3
4
5
6
7
8
NC = NO CONNECT
Rev. I | Page 8 of 24
(Not to Scale)
AD7417
TOP VIEW
16
15
14
13
12
11
10
9
NC
CONVST
V
A0
A1
A2
A
A
DD
IN4
IN3
OTI
setpoint register. The signal is reset at the end of a
Operating Modes
section).