MS-156-HRMJ-2 Hirose Electric Co Ltd, MS-156-HRMJ-2 Datasheet - Page 5

• Manufacturer Part Number: MS-156-HRMJ-2
• Description: CONN ADAPT MS-156 PLUG/SMA JACK
• Manufacturer: Hirose Electric Co Ltd

Specifications of MS-156-HRMJ-2

• Adapter Type: Plug to Jack
• Adapter Series: SMA to MS-156
• Center Gender: Female to Male
• Convert From (adapter End): MS-156 Plug, Male Pin
• Convert To (adapter End): SMA Jack, Female Socket
• Conversion Type: Between Series
• Style: Straight
• Mounting Type: Free Hanging (In-Line)
• Connector Type: SMA
• Frequency Range: DC to 6 GHz
• Housing Material: Phosphor Bronze
• Mounting Angle: Straight
• Operating Temperature Range: - 40 C to + 85 C
• Rf Series: SMA
• Product: Various Connectors
• Gender: Male / Female
• Contact Plating: Gold
• Shell Plating: Gold
• Impedance: 50 Ohms
• Termination Style: Cable
• Convert From: Plug
• Convert To: SMA Jack
• Side 1 Rf Series: MS-156
• Side 2 Rf Series: SMA
• Side 2 Gender: Jack (Female)
• Adapter Style: Straight
• Body Material: Phosphor Bronze
• Side 1 Gender: Jack (Female)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: *MS-156-HRMJ-2; H11398

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
BPrecautions
1. This product is intended to be used for circuit inspection only. Consult us if any other application is
2. Cross-hatched area shown on the PCB mounting pattern must be free of any conducive traces. Placing
3. Do not use hand soldering for mounting of MS-156HF.
4. Exercise caution as not to allow any debris to enter the board mounted MS-156HF when cutting PCB.
5. Do not use the washing process.
6. Please refrain from using the product in environments specifically affected by excessive vibration, shock,
7. For use of this product, be sure to put contact area of plug on position P(P4 full view) perpendicularly.
8. Plugs can be roughly classified to two types.
9. When automatic inspections are to be performed during the manufacturing operations, request the MS-
considered.
conductive traces in this area may affect performance and will void product warranties.
When the bottom surface of the product (i.e., the
diagram on the previous page) has been processed with a susbtrate copper trace and resist processing,
Hirose Electric will not be able to warrant the product.
dust, high humidity, gases, very high temperatures and very low temperatures such as outdoor
equipment. It might cause degradation or destruction of the product.Even if it endures during a short time,
long time quarification is not quaranteed.
- For mass production line automatic check (Press down type)
- For manual check (With retentive lock) : Unable to be used at production line.
156 plug connector manual for examples of implementation.
Doing so could result in solder and flux wicking to the contact areas.
Recommended Mounting of MS-156HF coaxial switch
on the PCB during the manufacturing process
To avoid contamination when cutting-off,
do not place PCB bridge close to the
mounted MS-156HF.
MS-156HF Series●Subminiature Coaxial Switch 1.6 mm High, DC to 6 GHz
shaded area of the specified land dimensions
MS-156HF
5