MHL1ECTTP5N6S KOA Speer Electronics, MHL1ECTTP5N6S Datasheet - Page 4

• Manufacturer Part Number: MHL1ECTTP5N6S
• Description: Common Mode Inductors 5.6nH +/-0.3nH
• Manufacturer: KOA Speer Electronics

Specifications of MHL1ECTTP5N6S

• Dimensions: 0.5 mm W x 1 mm L x 0.5 mm H
• Product: Inductors
• Shielding: Unshielded
• Test Frequency: 300 MHz
• Inductance: 5.6 nH
• Tolerance: 0.3 nH
• Maximum Dc Current: 300 mAmps
• Maximum Dc Resistance: 0.27 Ohms
• Self Resonant Frequency: 5400 MHz
• Operating Temperature Range: - 40 C to + 125 C
• Termination Style: SMD/SMT
• Package / Case: 0402 (1005 metric)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

5. Characteristics
Bolivar Drive
Spec ific ation s given herein m ay be c hang ed at an y tim e w itho ut prior not ice. Plea se co nfirm t echn ic al spec ific ations b efore yo u orde r and/ or us e.
Item
Operating Temperature
Storage Temperature
Resistance to Solder
Heat
Solderability
Leach Resistance
Insulation Resistance
Solvent Resistance
Terminal Strength
(hanging test)
Terminal Strength
(push test)
Bending Strength
P.O. Box 547
Requirement
-55°C to +125°C
40°C @ 70% Humidity
Change in Impedance: Relative to value before
test ±20%.
Appearance: There shall be no cracking
Solder Coverage: More than 75% of the terminal
electrode shall be covered with solder.
Solder Coverage: More than 95% of the
termination shall be covered with solder.
Appearance: There shall be no visible signs of
physical or mechanical damage (i.e. no cracks)
Terminations: Termination must not be leached
away for more than 5%.
Insulation Resistance: Min 1G ohms
Change in Impedance: Relative to value before
test ±10%.
Appearance: The terminal electrode shall not
break off, nor shall there be damage to the body.
Appearance: There shall be no evidence of
mechanical degradations to terminals or body.
Appearance: There shall be no physical or
mechanical damage
Impedance: Relative to initial value before test ±10%
Bradford, PA 16701
USA
814-362-5536
Conditions
Sealed plastic bags with desiccant shall be
used to reduce the potential of oxidation on
the terminations during storage.
Flux: 5-10 sec dip
After Flux: Air dry for 15 sec
Preheat: 150°C ±10°C
Preheat Time: 60 sec
Solder Temp: 260°C ±5°C
Dip Time: 10 ±1 sec
Flux: 5-10 sec dip
After Flux: Air dry for 15 sec
Solder Temp: 245°C ±5°C
Dip Time: 5 ±0.5 sec
The bead shall be subjected to the following
5 steps for the period of time shown below.
The 5 steps constitute one (1) rotation.
4 rotations shall be carried out.
1) Flux: 5-10 sec
2) After Flux: Air dry for 15 sec
3) Solder Temp: 230°C ±5°C
4) Dip Time: 5 ±0.5 sec
5) Cool: Air cool for 60 seconds
Cleaning by: Washer: Ultrasonic washer (100W)
Solvent: Isopropyl alcohol
Time: 3 minutes
Board: 90x40x1.6mm
Bend: 1mm
Time: 5 sec
Fax [phone]
Type
Type
1E
1E
1J
1J
W(kgf)
W(kgf)
0.5
1.4
––
––
www.koaspeer.com
30 sec ±2 sec
60 sec
PAGE 4 OF 6
Time
Time
SS-222 R12
N/A
N/A