MMA7260Q Freescale Semiconductor, MMA7260Q Datasheet - Page 3

• Manufacturer Part Number: MMA7260Q
• Description: SENSOR ACCEL 3-AXIS +/-1.5 16QFN
• Manufacturer: Freescale Semiconductor

Specifications of MMA7260Q

• Axis: X, Y, Z
• Acceleration Range: ±1.5g, 2g, 4g, 6g (Config)
• Sensitivity: 800mV/g, 600mV/g, 300mV/g, 200mV/g
• Voltage - Supply: 2.2 V ~ 3.6 V
• Output Type: Analog
• Bandwidth: 350Hz - X, 150Hz - Z
• Mounting Type: Surface Mount
• Package / Case: 16-QFN
• Sensing Axis: X, Y, Z
• Acceleration: 1.5 g, 2 g, 4 g, 6 g
• Maximum Operating Temperature: + 105 C
• Minimum Operating Temperature: - 40 C
• For Use With: RD3152MMA7260Q - BOARD REF 3-AXIS ACCELEROMETERRD3112MMA7260QE - BOARD DEMO STAR FOR MMA7260QT
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Interface: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Table 2. Operating Characteristics
Unless otherwise noted: –40°C < T
1. For a loaded output, the measurements are observed after an RC filter consisting of a 1.0 kΩ resistor and a 0.1 µF capacitor on V
2. These limits define the range of operation for which the part will meet specification.
3. Within the supply range of 2.2 and 3.6 V, the device operates as a fully calibrated linear accelerometer. Beyond these supply limits the device
4. This value is measured with g-Select in 1.5g mode.
5. The device can measure both + and – acceleration. With no input acceleration the output is at midsupply. For positive acceleration the output
6. These values represent the 10th percentile, not the minimum.
7. These values represent the 90th percentile, not the maximum.
8. The response time between 10% of full scale V
9. The response time between 10% of full scale Sleep Mode input voltage and 90% of the final operating output voltage.
10. A measure of the device’s ability to reject an acceleration applied 90 from the true axis of sensitivity.
11. Zero-g offset ratiometric error can be typically >20% at V
Sensors
Freescale Semiconductor
Operating Range
Output Signal
Noise
Control Timing
Output Stage Performance
Nonlinearity, X
Cross-Axis Sensitivity
Ratiometric Error
Supply Voltage
Supply Current
Supply Current at Sleep Mode
Operating Temperature Range
Acceleration Range, X-Axis, Y-Axis, Z-Axis
Zero-g (T
Zero-g
Sensitivity (T
Sensitivity
Bandwidth Response
RMS (0.1 Hz – 1 kHz)
Power Spectral Density RMS (0.1 Hz – 1 kHz)
Power-Up Response Time
Enable Response Time
Sensing Element Resonant Frequency
Internal Sampling Frequency
may operate as a linear device but is not guaranteed to be in calibration.
will increase above V
factory for additional information
g-Select1 & 2: 00
g-Select1 & 2: 10
g-Select1 & 2: 01
g-Select1 & 2: 11
X-axis
Y-axis
Z-axis
1.5g
2g
4g
6g
X-axis
Y-axis
Z-axis
XY
Z
XY
Z
Full-Scale Output Range (I
(4)
A
(4)
= 25°C, V
OUT
A
= 25°C, V
(2)
(11)
(3)
, Y
OUT
(10)
DD
DD
(4)
, Z
(9)
/2. For negative acceleration, the output will decrease below V
= 3.3 V)
DD
Characteristic
OUT
(8)
= 3.3 V)
OUT
(4)
(5)
= 30 µA)
A
< 105°C, 2.2 V < V
(4)
DD
input voltage and 90% of the final operating output voltage.
DD
DD
= 2.2 V. Sensitivity ratiometric error can be typically >3% at V
< 3.6 V, Acceleration = 0g, Loaded output
t
V
Symbol
RESPONSE
V
t
XY, XZ, YZ
ENABLE
f
f
NL
OFF
V
S
n
GCELL
GCELL
V
S,T
n
error
f
f
V
f
g
g
g
g
S
S
S
I
I
-3dB
-3dB
RMS
CLK
T
PSD
DD
DD
OFF
1.5g
FSO
DD
FS
FS
FS
FS
OUT
2g
4g
6g
A
, T
A
A
DD
V
±0.02
±0.01
±0.01
±2.6
±5.8
±1.0
SS
/2.
1.485
277.5
Min
–1.0
–40
740
555
185
2.2
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
+0.25
(6)
(6)
(6)
(6)
(6)
(6)
±0.02
±0.01
±0.00
Typ
±1.5
±2.0
±4.0
±6.0
1.65
±0.6
±5.8
±0.8
500
800
600
300
200
350
150
350
3.3
3.0
4.7
1.0
0.5
6.0
3.4
—
11
—
—
—
—
(1)
V
±0.02
±0.01
±0.01
DD
±3.8
±5.9
±0.8
1.815
322.5
Max
+105
+1.0
800
860
645
215
3.6
2.0
2.0
5.0
10
—
—
—
—
—
—
—
—
—
—
—
—
–0.25
(7)
(7)
(7)
(7)
(7)
(7)
DD
= 2.2. Consult
MMA7260QT
μg/
mVrms
DD
%FSO
mg/°C
Unit
mV/g
mV/g
mV/g
mV/g
%/°C
kHz
kHz
kHz
ms
ms
μA
μA
Hz
Hz
°C
%
%
-GND.
V
V
V
g
g
g
g
Hz
3