SC16C650BIB48 NXP Semiconductors, SC16C650BIB48 Datasheet - Page 27

• Manufacturer Part Number: SC16C650BIB48
• Description: UART, 32BYTE FIFO, 16C650, LQFP48
• Manufacturer: NXP Semiconductors

Specifications of SC16C650BIB48

• No. Of Channels: 1
• Data Rate: 3Mbps
• Supply Voltage Range: 2.25V To 5.5V
• Operating Temperature Range: -40°C To +85°C
• Digital Ic Case Style: LQFP
• No. Of Pins: 48
• Svhc: No SVHC (18-Jun-2010)
• Operating: RoHS Compliant
• Uart Features: Automatic Software/Hardware Flow Control, Programmable Xon/Xoff Characters
• Rohs Compliant: Yes

NXP Semiconductors
SC16C650B_4
Product data sheet
7.10 Enhanced Feature Register (EFR)
7.9 Scratchpad Register (SPR)
The SC16C650B provides a temporary data register to store 8 bits of user information.
Enhanced features are enabled or disabled using this register.
Bits 0 through 4 provide single or dual character software flow control selection. When the
Xon1 and Xon2 and/or Xoff1 and Xoff2 modes are selected, the double 8-bit words are
concatenated into two sequential numbers.
Table 22.
Bit
7
6
5
4
3:0
Symbol
EFR[7]
EFR[6]
EFR[5]
EFR[4]
EFR[3:0]
Enhanced Feature Register bits description
Description
Automatic CTS flow control.
Automatic RTS flow control. Automatic RTS may be used for hardware flow
control by enabling EFR[6]. When Auto-RTS is selected, an interrupt will be
generated when the receive FIFO is filled to the programmed trigger level and
RTS will go to a logic 1 at the next trigger level. RTS will return to a logic 0 when
data is unloaded below the next lower trigger level (programmed trigger level 1).
The state of this register bit changes with the status of the hardware flow
control. RTS functions normally when hardware flow control is disabled.
Special Character Detect.
Enhanced function control bit. The content of IER[7:4], ISR[5:4], FCR[5:4], and
MCR[7:5] can be modified and latched. After modifying any bits in the
enhanced registers, EFR[4] can be set to a logic 0 to latch the new values. This
feature prevents existing software from altering or overwriting the SC16C650B
enhanced functions.
Cont-3:0 Tx, Rx control. Logic 0 or cleared is the default condition.
Combinations of software flow control can be selected by programming these
bits. See
logic 0 = Automatic CTS flow control is disabled (normal default condition)
logic 1 = enable Automatic CTS flow control. Transmission will stop when
CTS goes to a logic 1. Transmission will resume when the CTS pin returns to
a logic 0.
0 = Automatic RTS flow control is disabled (normal default condition)
1 = enable Automatic RTS flow control
logic 0 = special character detect disabled (normal default condition)
logic 1 = special character detect enabled. The SC16C650B compares each
incoming receive character with Xoff2 data. If a match exists, the received
data will be transferred to FIFO and ISR[4] will be set to indicate detection of
special character. Bit 0 in the X-registers corresponds with the LSB bit for the
receive character. When this feature is enabled, the normal software flow
control must be disabled (EFR[3:0] must be set to a logic 0).
logic 0 = disable (normal default condition)
logic 1 = enable
Rev. 04 — 14 September 2009
Table
23.
UART with 32-byte FIFOs and IrDA encoder/decoder
SC16C650B
© NXP B.V. 2009. All rights reserved.
27 of 48