ARXP1124 PANASONIC EW, ARXP1124 Datasheet - Page 4

• Manufacturer Part Number: ARXP1124
• Description: HIGH FREQUENCY RELAY 2.5GHZ, 24VDC, SPDT
• Manufacturer: PANASONIC EW

Specifications of ARXP1124

• Coil Frequency Max: 2.5GHz
• Coil Voltage Vdc Nom: 24V
• Contact Current Max: 500mA
• Contact Voltage Dc Nom: 30V
• Coil Resistance: 2.88kohm
• Contact Configuration: SPDT
• Coil Type: DC
• Vswr: 1.2
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

RX-P (ARXP)
DIMENSIONS
NOTES
1. Coil operating power
Pure DC current should be applied to the
coil. The wave form should be rectangular.
If it includes ripple, the ripple factor should
be less than 5%.
However, check it with the actual circuit
since the characteristics may be slightly
different.
2. Coil connection
When connecting coils, refer to the wiring
diagram to prevent mis-operation or
malfunction.
To ensure accurate operation, the voltage
on both sides of the coil should be 5% (at
20C 68F) of the nominal coil voltage.
Also, please note that the pick-up and drop-
out voltages (set and reset voltages) will
change depending on operation
temperature and conditions of use.
Keep the coil allowable voltage ripple ratio
to no more than 5%.
3. External magnetic field
Since RX-P relays are highly sensitive
polarized relays, their characteristics will be
affected by a strong external magnetic field.
Avoid using the relay under that condition.
4
CAD Data
7-0.40 to 0.45 dia.
7-.016 to .018 dia.
Solder to the
PC board earth.
2-0.6x0.3
2-.024x.012
.362
(mm inch)
9.2
2.63
.104
.008
0.2
External dimensions
2.54
.100
Interested in CAD data? You can obtain CAD data for all products with a
from
20.5
.807
Tolerance: 0.3
your local Panasonic Electric Works representative.
Part No.
Lot No.
4. Cleaning
For automatic cleaning, the boiling method
is recommended. Avoid ultrasonic cleaning
which subjects the relays to high frequency
vibrations, which may cause the contacts to
stick.
It is recommended that alcoholic solvents
be used.
5. Soldering
1) Please meet the following conditions if
this relay is to be automatically soldered.
(1) Preheating: Max. 120C
solder surface) for max. 120 seconds
(2) Soldering: Max. 2605C
max. 6 seconds
2) Please meet the following conditions if
this relay is to be soldered by hand.
(1) 260C
(2) 350C
*In addition, when soldering the case to the
PC board, the plating may swell depending
on the soldering conditions.
6. Conditions for operation, transport
and storage conditions
1) Ambient temperature, humidity, and
atmospheric pressure during usage,
transport, and storage of the relay:
(1) Temperature:
–40 to +70C
when 60 to 70C
time is 1 second maximum and ON time is
10% maximum.)
12.4
.488
3.0
.118
(2.04)
(.080)
.012
500F
662F
–40 to +158F
7.62
.300
for max. 10 seconds
for max. 3 seconds
140 to
(2.74)
(.108)
158F, the pulse
(Deenergized condition)
248F
(However,
NC
50041F
-
Single side stable
14
1
13
(terminal
12
COM
11
7.62
.300
10
for
9
2.54
.100
NO
PC board pattern (Bottom view)
+
7
8
0.90
.035
0.9 dia. hole
.035 dia. hole
Schematic (Bottom view)
(2) Humidity: 5 to 85% RH
(Avoid freezing and condensation.)
The humidity range varies with the
temperature. Use within the range indicated
in the graph below.
(3) Atmospheric pressure: 86 to 106 kPa
Temperature and humidity range for usage,
transport, and storage:
2) Condensation
Condensation forms when there is a
sudden change in temperature under high
temperature and high humidity conditions.
Condensation will cause deterioration of the
relay insulation.
3) Freezing
Condensation or other moisture may freeze
on the relay when the temperature is lower
than 0C 32F. This causes problems such
as sticking of movable parts or operational
time lags.
4) Low temperature, low humidity
environments
The plastic becomes brittle if the relay is
exposed to a low temperature, low humidity
environment for long periods of time.
RESET
+
(Reset condition)
14
1
(Avoid freezing
when used at
temperatures
lower than
0°C 32°F)
2.54
.100
1 coil latching
-40
-40
13
12
COM
Tolerance range
11
ds_61307_en_rxp: 280708J
10
85
2 coil latching only
5
32
9
SET
R 0.45
0
-
(Avoid
condensation
when used at
temperatures
higher than
0°C 32°F)
Temperature, °C
Humidity, %R.H.
7
8
CAD Data
.018
Tolerance: 0.1
RESET
-
(Reset condition)
14
1
2 coil latching
°F
13
158
70
mark
12
COM
11
10
.004
+
6
9
SET
+
7
8