HW9Z-LS IDEC, HW9Z-LS Datasheet
HW9Z-LS
Specifications of HW9Z-LS
Related parts for HW9Z-LS
HW9Z-LS Summary of contents
Page 1
... HW Series Dual Pushbutton Switches ...
Page 2
... Operating extremes Hz, amplitude 0.5 mm Mechanical Life 500,000 operations minimum Electrical Life 500,000 operations minimum Degree of Protection IP40 (IP65 when using HW9Z-D7D rubber boot) 2 Dual Pushbutton Switches Applications: Ideal for use as power switches and start/stop switches (available with I/ON and O/OFF markings on the buttons and a pilot light in the center) ...
Page 3
... Recommended vertical spacing: 100 mm 30 The minimum mounting centers are applicable to switches with one layer of contact blocks (two contact blocks). When two layers of con- tact blocks are mounted, determine the minimum mounting centers in consideration of convenience for wiring. ...
Page 4
... Flush (top) Flush (bottom) Momentary Flush (top) Extended (bottom) Flush (top) Flush (bottom) Interlock Flush (top) Extended (bottom) 4 Dual Pushbutton Switches with Pilot Light HW7D MAU Operating type 1: Momentary 2: Interlock Button style 1: Flush + Flush 2: Flush + Extended Contact arrangement code (top button) 10: 1NO ...
Page 5
... Note: Full voltage types do not contain a lamp. Order LED or incandescent lamps separately. For lamps, see page 9. LED illuminated transformer and DC-DC converter types contain an LED lamp (LSTD-6 , rated voltage 6V AC/DC). Incandescent illuminated transformer types contain an incandescent lamp (LS-6, rated voltage 6V AC/DC). HW Dual Pushbutton Switches Series Contact Arrangement Input Type ...
Page 6
... HW Dual Pushbutton Switches Series Contact Arrangement Chart Contact Arrangement Top Button Bottom Button Contact Code 1NO 1NO 1NO 1NC 1NC 1NO 1NC 1NC 1NO 2NO 1NO 1NO-1NC 1NO 2NC 1NC 2NO 1NC 1NO-1NC 1NC 2NC 2NO 1NO 2NO 1NC 1NO-1NC ...
Page 7
... Bottom Button Contact Code 2NC 1NO 2NC 1NC 2NO 2NO 2NO 1NO-1NC 2NO 2NC 1NO-1NC 2NO 1NO-1NC 1NO-1NC 1NO-1NC 2NC 2NC 2NO 2NC 1NO-1NC 2NC 2NC HW Dual Pushbutton Switches Series Contact Block Top Button Type Normal Mounting Position 0210 Dummy 0201 Dummy ...
Page 8
... OB-31PN05 5 LW9Z-BM LW9Z-BM 1 HW-VG1 HW-VG1PN10 10 HW9Z-A25 HW9Z-A25PN05 5 HW9Z-LS HW9Z-LSPN10 10 Dimensions (mm) Degree of protection: IP65 22.5 33 Used to tighten the locking ring when installing the HW switch onto a panel. Tighten the locking ring to a torque of 2.0 N·m. 110 Used to install and remove the LED/incandescent lamps. ...
Page 9
HW Series Maintenance Parts LED Lamps (LSTD Type) Rated Current Operating Voltage AC 6V AC/DC ±10 ( (G, S) 12V AC/DC ±10 24V AC/DC ±10 Incandescent Lamps (LS Type) ...
Page 10
... Safety Lever Lock IDEC strongly recommends using the safety lever lock (HW9Z-LS, yellow) to prevent heavy vibration or mainte- nance personnel from unlocking the contact assembly series can be mounted vertically with a minimum spacing but spacing should be determined to ensure easy operation (recommended minimum spacing: 100 mm) ...
Page 11
... Installing the Rubber Boot When using the HW7D pushbuttons in places where the pushbuttons are subjected to water splash or an excessive amount of dust, make sure to use the HW9Z-D7D rubber boot (IP65) which is ordered separately. Notes for Installing the Rubber Boot Remove the gasket from the operator, and install the rubber boot on the operator ...
Page 12
... Specifications and other descriptions in this catalog are subject to change without notice. IDEC CORPORATION (USA) 1175 Elko Drive, Sunnyvale, CA 94089-2209, USA Tel: +1-408-747-0550, Toll Free: (800) 262-IDEC, Fax: +1-408-744-9055 E-mail: opencontact@idec.com, www.idec.com IDEC CANADA LIMITED Unit 22-151, Brunel Road Mississauga, Ontario, L4Z 1X3, Canada ...