A1184LUA Allegro Microsystems Inc, A1184LUA Datasheet - Page 12

• Manufacturer Part Number: A1184LUA
• Description: IC SWITCH HALL EFFECT UNI 3-SIP
• Manufacturer: Allegro Microsystems Inc
• Type: Unipolar Switchr

Specifications of A1184LUA

• Sensing Range: 300G ~ 600G - Programmable, Fixed Release
• Voltage - Supply: 3.5 V ~ 24 V
• Current - Supply: 6.9mA
• Output Type: Digital, Differential
• Features: Programmable
• Operating Temperature: -40°C ~ 150°C
• Package / Case: 3-SIP
• Magnetic Type: Unipolar
• Operating Supply Voltage (min): 3.5V
• Operating Supply Voltage (typ): 5/9/12/15/18V
• Operating Supply Voltage (max): 24V
• Mag Sensor Operate Point (g): 600Gs
• Mag Sensor Hysteresis(g): 15Gs
• Package Type: Ultra Mini SIP
• Pin Count: 3
• Mounting: Through Hole
• Operating Temp Range: -40C to 150C
• Operating Temperature Classification: Automotive
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Current - Output (max): -
• Lead Free Status / RoHS Status: Not Compliant, Contains lead / RoHS non-compliant

A1184
The pulse sequences consist of the following groups of pulses:
1. An enable sequence.
2. A bitfield address sequence.
3. When permanently setting the bitfield, a long V
4. When permanently setting the bitfield, the level of V
Bitfields that are not set are evaluated as zeros. The bitfield-level
fuses for 0 value bitfields are never blown. This prevents inad-
ing pulse. (Note: Blown bit fuses cannot be reset.)
be allowed to drop to zero between each pulse sequence, in
order to clear all registers. However, when provisionally set-
ting bitfields, V
sequences, in order to maintain the prior bitfield settings while
preparing to set additional bitfields.
CC
must be maintained at V
V
V
V
V
V
V
PM
PH
PL
PM
PH
PL
0
0
V+
V+
Figure 5. Pulse sequence to provisionally try calibration value 5.
Figure 6. Pulse sequence to permanently encode calibration value 5 (101 binary, or
bitfield address 3 and bitfield address 1).
Chopper-Stabilized Unipolar Hall Effect Switch
Enable
Enable
PL
between pulse
Try 5
Encode 00100
PH
Standard Two-Wire Field-Programmable
10
fuse-blow-
Address
Address
CC
2
must
(4
10
)
Blow
Monitoring
Optional
vertently setting the bitfield to 1. Instead, blowing the device-
level fuse protects the 0 bitfields from being accidentally set in
the future.
When provisionally trying the calibration value, one pulse
sequence is used, using decimal values. The sequence for setting
the value 5
When permanently setting values, the bitfields must be set indi-
vidually, and 5
set to 1 (000100
which is 1
sequences for permanently setting the calibration value 5 are
shown in figure 6. The final V
period, enough to blow the corresponding bitfield-level fuse.
Clear
t
10
Enable
10
). Bit 2 is ignored, and so remains 0.Two pulse
is shown in figure 5.
10
Encode 00001
2
, which is 4
must be programmed as binary 101. Bit 3 is
Address
2
Blow
(1
115 Northeast Cutoff
1.508.853.5000; www.allegromicro.com
Allegro MicroSystems, Inc.
Worcester, Massachusetts 01615-0036 U.S.A.
10
)
10
PH
), then bit 1 is set to 1 (000001
pulse is maintained for a longer
t
2
,
11