ABL014-00 NVE, ABL014-00 Datasheet
ABL014-00
Specifications of ABL014-00
Related parts for ABL014-00
ABL014-00 Summary of contents
Page 1
... GT Sensors Precision Gear Tooth and Encoder Sensors NVE’s GT Sensor products are based on a Low Hysteresis GMR sensor material and are designed for use in industrial speed applications where magnetic detection of gear teeth and magnetic encoder wheels is required. GT Sensors with both analog and digital outputs are available. The analog parts feature the large signal and robust characteristics which NVE’ ...
Page 2
... The ABL-Series GT Sensors are differential sensor elements that provide an analog sinusoidal output signal when used with a bias magnet and gear tooth or a magnetic encoder. These chips use NVE’s proprietary GMR sensor elements featuring an extremely large output signal from the raw sensor element, which is stable over the rated temperature and voltage range ...
Page 3
... Linearity and Hysteresis measured across linear operating range, unipolar operation. 3. Application of a magnetic field in excess of this value will saturate the GMR sensor elements and no further output will be obtained. No damage occurs to the sensor elements when saturated. NVE GMR sensors will not be damaged by any large magnetic field. 4. ...
Page 4
... IC Drawings: ABL004 ABL005 ABL014 1.000 0.250 ABL015 0.500 0.125 - All dimensions All resistors are 5k - Sensor elements are located symmetrically about the center of the IC. Note: ABL006 ABL016 Sensor Element Size and Spacing Not Shown www.nve.com Center of Die and Package 0.140 1.000 0.500 ...
Page 5
... ABL004, ABL005, ABL006 Schematic VCC1 R4 R1 OUT GND1 Part Numbers and Configurations: Single or Dual Part Number Bridge ABL004-00 Single ABL005-00 Single ABL006-00 Single ABL014-00 Dual ABL015-00 Dual ABL016-00 Dual ABL004-10 Single ABL005-10 Single ABL006-10 Single ABL014-10 Dual ABL015-10 Dual ABL016-10 Dual www.nve.com ...
Page 6
... No Connect ABL004-00, ABL005-00, No Connect ABL006-00 Ground TDFN6 Package Out+ ABL004-10, No Connect ABL005-10, ABL006-10 ABL006-10 Gnd www.nve.com VCC Ground1 No Connect Out-1 ABL014-00, ABL015-00, No Connect Out+1 ABL016-00 Out- VCC1 Ground1, VCC Ground2 ABL014-10, No Connect Out-1 ABL015-10, ABL016-10 Out- Out phone: 952-829-9217 fax: 952-829-9189 ...
Page 7
... Linear and Angular Position Sensing Description: NVE offers these products specifically for use as sensors for gear tooth wheels or magnetic encoders with a digital output signal. The pulse output from the sensor corresponds with the gear teeth passing in front of it. When a gear tooth or magnetic pole is in front of the sensor, the sensor’s output goes high ...
Page 8
... Supply currents can be factory programmed to different levels, for example 3 mA and 6 mA and 14 mA; contact NVE for details. 3. Pin-to-pin voltage, Human Body Model for ESD 4. Airgap measured with standard ferrous gear tooth; contact NVE for details. www.nve.com Min Typ 4.5 3.2 4 ...
Page 9
... Voltage Regulator GMR A Bridge EEPROM Gain Packages: The AKL-Series parts are available in the TDFN8 SO8 package. Please see the package drawing section in the Appendix for dimensions. www.nve.com Element Spacing (Microns) Marking 1000 Part Number 500 Part Number 300 Part Number ...
Page 10
... AKL003-12 TEST BRIDGE+ Sensitivity www.nve.com Note: Bridge + and Bridge - are provided for analysis purposes only. NVE does not TEST recommend connecting these pins in a production product for ESD and loading BRIDGE- reasons. Also, all pins labeled “Test” must be floating, i.e., not connected to each other or any other circuit node ...