M/58303/01 NORGREN, M/58303/01 Datasheet - Page 2

• Manufacturer Part Number: M/58303/01
• Description: FLAT SUCTION CUP, 10MM
• Manufacturer: NORGREN

Specifications of M/58303/01

• Cup Type: Flat
• Outer Diameter: 10mm
• Svhc: No SVHC (18-Jun-2010)
• External Diameter: 10mm
• Temperature Max: 70°C
• Temperature Min: -10°C
• Lead Free Status / RoHS Status: na

Lifting Force
R = Minimum radius of work surface, S = Maximum movement, V = Volume inside
Note: Theoretical values are given in this table. Always allow a safety factor of > 2.
Weights for Suction Cups
Basic Dimensions
Warning
These products are intended for use in industrial compressed air sys-
tems only. Do not use these products where pressures and tempera-
tures can exceed those listed under ‘Technical Data’.
Before using these products with fluids other than those specified,
for non-industrial applications, life-support systems, or other applica-
tions not within published specifications, consult NORGREN.
Through misuse, age, or malfunction, components used in
fluid power systems can fail in various modes.
N/UK 3.5.011.02
Model
Fy (N)-0,6 bar 1,5
R
S
V
Model
Weight (kg)
Model
A
C
G
H
SW (A/F)
SW
D
I
6 to 30
-0,2 bar 0,5
-0,9 bar 2,3
(mm)
(mm)
(cm
ø D
G
3
)
58301
6
0,001
58301
6
4,5
-
M 5
15
-
8
58301
6
5
1,5
0,017
Fy
M/58300
58302
8
0,001
58302
8
4,5
-
M 5
16
-
8
58302
8
1
2,5
3,5
7
1,5
0,041
SW
40 and 50
58303
10
0,001
58303
10
4,5
-
M 5
20
-
8
ø D
58303
10
1,5
4
6
9
2
0,065
ø I
G
Fx =
58304
15
0,001
58304
15
4,5
-
M 5
21
-
8
58304
15
2,7
12
12
4
0,330
8
Our policy is one of continued research and development. We therefore reserve the right
• Fy
to amend, without notice, the specifications given in this document.
Fx
58305
20
0,008
58305
20
8
-
G 1/8 A
19,5
-
14
58305
20
5
15,5
23
13
2
0,500
58306
25
0,010
58306
25
8
-
G 1/8 A
20
-
14
58306
25
9
26,5
40
17,5
2,5
0,750
ø D
ø I
G
80
The system designer is warned to consider the failure modes of
all component parts used in fluid power systems and to provide ade-
quate safeguards to prevent personal injury or damage to equipment
in the event of such failure.
System designers must provide a warning to end users in the
system instructional manual if protection against a failure mode
cannot be adequately provided.
System designers and end users are cautioned to review specific
warnings found in instruction sheets packed and shipped with
these products.
58307
30
0,012
58307
30
8
-
G 1/8 A
20,5
-
14
58307
30
11
34
51
26
2,5
1,3
R
SW
58308
40
0,011
58308
40
6
9
G 1/8
23
24
14
58308
40
19
57,5
86
37
3,5
3
58309
50
30
91
135
41
4
4,2
58309
50
0,016
58309
50
6
11
G 1/8
26
26
14
58310
80
86
260
390
100
6
21
58310
80
0,058
58310
80
13
3,5
G 1/8
21,5
53
19
120 and 150
ø D
ø I
G
58311
120
180
540
810
365
6
82
58311
120
0,359
58311
120
9,5
-
G 1/2
34,5
65
-
58312
150
280
842
1250
380
9
177
58312
150
0,590
58312
150
9,5
-
G 1/2
41,5
65
-
5/96