E3S-CL2 Omron, E3S-CL2 Datasheet - Page 10

• Manufacturer Part Number: E3S-CL2
• Description: 50CM, ADJ SENSING DIST, NPN/PNP
• Manufacturer: Omron
• Series: E3S-CLr

Specifications of E3S-CL2

• Rohs Compliant: YES
• Sensing Distance: 0.197" ~ 7.874" (5mm ~ 200mm) ADJ
• Sensing Method: Reflective, Diffuse
• Sensing Object: Black Paper, White Paper
• Output Configuration: NPN/PNP - Dark-ON/Light-ON - Selectable
• Sensing Light: Infrared
• Mounting Type: Bracket Mount
• Current - Supply: 35mA
• Voltage - Supply: 10 V ~ 30 V
• Package / Case: Module, Pre-Wired
• Features: NPN/PNP Selectable Output
• Sensing Range: 50mm To 500mm
• Sensor Output: Open Collector
• Supply Voltage Range Dc: 10V To 30V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

H
Mounting Direction
Mount the Sensor so that the detection face runs parallel to the sur-
face of the object being detected and not at an angle (see below).
If detecting a shiny object, mount the Sensor so that the detection
face is at an angle of between 5_ and 10_ of the surface of the object
being detected. Check to be sure that there is no interference from
the background (see below).
If stable operation is not possible near a mirror surface, mount the
Sensor at an angle as shown below, and separate the Sensor as far
as possible from the mirror surface.
Detected object
Cat. No. CEDSAX4
E3S-CL
1-800-55-OMRON
OMRON ELECTRONICS LLC
One East Commerce Drive
Schaumburg, IL 60173
MOUNTING
NOTE: DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters to inches divide by 25.4.
Shiny object
Detection face
Surface of object de-
tected
Mirror surface
R
11/01
OMRON ON- -LINE
Global -- http://www.omron.com
USA -- http://www.omron.com/oei
Canada -- http://www.omron.com/oci
Specifications subject to change without notice.
Mount the Sensor so that it is not aligned with the direction of move-
ment of the detected object, as shown below.
Mount the Sensor so that it is not aligned with extreme changes in
color or materials, as shown below.
Mount the Sensor so that sunlight, fluorescent light, incandescent
light, or other strong sources of light do not enter the directional
angle of the Sensor.
Precautions
When mounting the Sensor, do not hit the Sensor with a hammer, or
any other object. This will cause the Sensor to lose its watertight-
ness.
Use M4 screws to mount the Sensor.
The tightening torque of each screw must be 12 kgf S m (1.18 N S m)
maximum.
Direct Mounting
Mount the Sensor as shown in the following illustration.
Correct
The E3S-CL is not a safety component for ensuring the safety
of people which is defined in EC directive (91/368/EEC) and
covered by separate European standards or by any other reg-
ulations or standards.
!
Detected
object
Direction of
movement
WARNING
Correct
Direction of
movement
Two, 4.5 dia.
through holes
Incorrect
Detected
object
M4 hole
Direction of
movement
OMRON CANADA, INC.
416-286-6465
885 Milner Avenue
Scarborough, Ontario M1B 5V8
Incorrect
Two, M3
Detected
object
Printed in U.S.A.
Direction of
movement
E3S-CL
M4 hole