AD7706BRZ Analog Devices Inc, AD7706BRZ Datasheet - Page 33

• Manufacturer Part Number: AD7706BRZ
• Description: IC,Data Acquisition Signal Conditioner,3-CHANNEL,16-BIT,CMOS,SOP,16PIN,PLASTIC
• Manufacturer: Analog Devices Inc

Specifications of AD7706BRZ

• Number Of Bits: 16
• Sampling Rate (per Second): 500
• Data Interface: DSP, MICROWIRE™, QSPI™, Serial, SPI™
• Number Of Converters: 1
• Power Dissipation (max): 1mW
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 16-SOIC (0.300", 7.50mm Width)
• Number Of Elements: 1
• Resolution: 16Bit
• Architecture: Delta-Sigma
• Sample Rate: 0.5KSPS
• Input Polarity: Unipolar/Bipolar
• Input Type: Voltage
• Differential Input: Yes
• Power Supply Requirement: Single
• Single Supply Voltage (typ): 3/5V
• Single Supply Voltage (min): 2.7V
• Single Supply Voltage (max): 5.25V
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Power Dissipation: 1mW
• Integral Nonlinearity Error: ±0.003%FSR
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 16
• Package Type: SOIC W
• Input Signal Type: Pseudo-Differential
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-AD7706EBZ - BOARD EVALUATION FOR AD7706
• Lead Free Status / Rohs Status: Compliant

CONFIGURING THE AD7705/AD7706
The AD7705/AD7706 contain six on-chip registers that the user
can access via the serial interface. Communication with any of
these registers is initiated by first writing to the communication
register. Figure 21 outlines a flowchart of the sequence used to
configure registers after a power-up or reset on the AD7705;
similar procedures apply to the AD7706.
WRITE TO COMMUNICATIONS REGISTER SETTING UP
NEXT OPERATION TO BE A READ FROM THE DATA
REGISTER (38 HEX)
WRITE TO COMMUNICATIONS REGISTER SELECTING
CHANNEL & SETTING UP NEXT OPERATION TO BE A
WRITE TO THE CLOCK REGISTER (20 HEX)
WRITE TO COMMUNICATIONS REGISTER SELECTING
CHANNEL & SETTING UP NEXT OPERATION TO BE A
WRITE TO THE SETUP REGISTER (10 HEX)
WRITE TO CLOCK REGISTER SETTING THE CLOCK
BITS IN ACCORDANCE WITH THE APPLIED MASTER
CLOCK SIGNAL AND SELECT UPDATE RATE FOR
SELECTED CHANNEL (0C HEX)
WRITE TO SETUP REGISTER CLEARING F SYNC,
SETTING UP GAIN, OPERATING CONDITIONS &
INITIATING A SELF-CALIBRATION ON SELECTED
CHANNEL (40 HEX)
CONFIGURE & INITIALIZE μC/μP SERIAL PORT
POWER-ON/RESET FOR AD7705
READ FROM DATA REGISTER
NO
POLL DRDY PIN
START
DRDY
LOW?
Figure 21. Flowchart for Setting Up and Reading from the AD7705
YES
Rev. C | Page 33 of 44
WRITE TO COMMUNICATIONS REGISTER SETTING UP NEXT
OPERATION TO BE A READ FROM THE COMMUNICATIONS
REGISTER (08 HEX)
The flowchart also shows two read options—one polls the DRDY
pin, and the other interrogates the DRDY pin. In addition,
Figure 21 shows a series of words that should be written to the
registers for the following operating conditions: Gain 1, no
filter sync, bipolar mode, buffer off, clock of 4.9512 MHz, and
output rate of 50 Hz.
WRITE TO COMMUNICATIONS REGISTER SETTING UP
NEXT OPERATION TO BE A READ FROM THE DATA
REGISTER (38 HEX)
POLL DRDY BIT OF COMMUNICATIONS REGISTER
READ FROM COMMUNICATIONS REGISTER
READ FROM DATA REGISTER
NO
DRDY
LOW?
YES
AD7705/AD7706