CS4207-CNZR Cirrus Logic Inc, CS4207-CNZR Datasheet - Page 68

• Manufacturer Part Number: CS4207-CNZR
• Description: Audio CODECs IC Lo Pwr,4/6 HD Aud Codec w/HP Amp
• Manufacturer: Cirrus Logic Inc

Specifications of CS4207-CNZR

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

68
6.6.10 Digital Converter Control
Get Parameter Command Format:
** Note: Address F0Eh is not supported.
Set Parameter Command Format:
Response Format:
The S/PDIF IEC Control (SIC) bits are supported in one of two ways. In the first case referred to as “Codec
Formatted SPDIF,” on an input PCM stream of less than 32 bits, the codec strips off the SIC bits before
transferring the samples to the system and puts them in the Digital Converter Control for later software
access.
In the second case, referred to as “Software Formatted (or Raw) SPDIF,” on a 32-bit input stream, the
entire stream is transferred into the system without the codec stripping any bits. However, the codec must
properly interpret the Sync Preamble bits of the stream and then send the appropriately coded preamble.
The IEC60958 specification, Section 4.3, “Preambles,” defines the preambles and the coding to be used.
Software will specify the “B,” “M,” or “W” (also known as “X,” “Y,” or “Z”) preambles by encoding the last
four bits of the preamble into the Sync Preamble section (bits 0-3) of the frame. The codec must examine
the bits specified and encode the proper preamble based on the previous state. The previous state is to
be maintained by the codec hardware.
Bits [31:28]
Bits [31:28]
CAd = X
CAd = X
31:16
14:8
Bits
15
7
6
5
4
3
2
1
0
Node ID = 07h
Node ID = 07h
Bits [27:20]
Bits [27:20]
Read/Write
Read Only
Read Only
Read Only
Read Only
Read Only
Read Only
Read Only
Read Only
Read Only
Read Only
Type
Verb ID = F0D/**
Verb ID =70D
Verb ID =70E
Bits [19:8]
Bits [19:8]
0000000b
Default
0000h
0b
0b
0b
0b
1b
1b
0b
0b
0b
Reserved
Reserved
CC[6:0] (Category Code): Programmed accord-
ing to IEC standards, or as appropriate.
L (Generation Level): Programmed according to
IEC standards, or as appropriate.
PRO (Professional): 1 indicates Professional use
of channel status; 0 indicates Consumer.
/AUDIO (Non-Audio): 1 indicates data is non-
PCM format; 0 indicates data is PCM.
COPY (Copyright): 1 indicates copyright is
asserted; 0 indicates copyright is not asserted.
PRE (Pre-emphasis): 1 indicates filter pre-
emphasis is 50/15 us; 0 pre-emphasis is none.
VCFG (Validity Config.): This bit is only defined
for Output Converters and is defined as
Reserved, with a Read Only value of 0 for Input
Converters.
V (Validity): This bit reflects the “Validity flag,”
transmitted in each subframe.
DigEn (Digital Enable): Enables or disables digi-
tal transmission. A 1 indicates that the digital
data can pass through the node. A 0 indicates
that the digital data is blocked from passing
through the node, regardless of the state.
Parameter ID =Bits[15:8]
Parameter ID =Bits[7:0]
Parameter ID = 00h
Description
Bits [7:0]
Bits [7:0]
CS4207
DS880F1