QS3861QG Integrated Device Technology (Idt), QS3861QG Datasheet - Page 4

• Manufacturer Part Number: QS3861QG
• Description: Bus Switch 1-Element 10-IN 24-Pin QSOP Tube
• Manufacturer: Integrated Device Technology (Idt)

Specifications of QS3861QG

• Package: 24QSOP
• Configuration: 10 x 1:1
• Logic Function: Bus Switch
• Number Of Elements Per Chip: 1
• Number Of Outputs Per Chip: 10
• Typical Operating Supply Voltage: 5 V
• Maximum On Resistance: 10(Typ) Ohm
• Maximum High Level Output Current: -120 mA
• Maximum Low Level Output Current: 120 mA
• Maximum Operating Supply Voltage: 5.25 V
• Minimum Operating Supply Voltage: 4.75 V
• Maximum Propagation Delay Time @ Maximum Cl: 0.25@5V ns

NOTES:
1. For conditions shown as Min. or Max., use the appropriate values specified under DC Electrical Characteristics.
2. Typical values are at V
3. Per TTL-driven input (V
3. This current applies to the control inputs only and represents the current required to switch internal capacitance at the specified frequency. The A and B inputs generate no significant
POWER SUPPLY CHARACTERISTICS
SWITCHING CHARACTERISTICS OVER OPERATING RANGE
T
C
NOTES:
1. Minimums are guaranteed but not production tested.
2. This parameter is guaranteed but not production tested.
3. The bus switch contributes no propagation delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone
IDTQS3861
HIGH-SPEED CMOS 10-BIT BUS SWITCH WITH FLOW-THROUGH PINOUT
A
LOAD
Symbol
Symbol
= -40°C to +85°C, V
AC or DC currents as they transition. This parameter is guaranteed but not production tested.
is of the order of 0.25ns at C
system. Propagation delay of the bus switch, when used in a system, is determined by the driving circuit on the driving side of the switch and its interaction with the load on
the driven side.
ΔI
I
I
t
t
t
t
t
t
CCQ
CCD
PZH
PHZ
PLH
PHL
PZL
PLZ
CC
= 50pF, R
Quiescent Power Supply Current
Power Supply Current per Input HIGH
Dynamic Power Supply Current per MHz
LOAD
Parameter
Data Propagation Delay
A to B, B to A
Switch Turn-On Delay
BE to A or B
Switch Turn-Off Delay
BE to A or B
= 500Ω unless otherwise noted.
CC
IN
CC
Parameter
= 3.4V, control inputs only). A and B pins do not contribute to ΔIcc.
= 5V and T
= 5V ± 5%
L
= 50pF. Since this time constant is much smaller than the rise and fall times of typical driving signals, it adds very little propagation delay to the
A
(2)
= 25°C.
(2)
(3)
(4)
V
V
V
BE Input Toggling @ 50% Duty Cycle
CC
CC
CC
= Max., V
= Max., V
= Max., A and B Pins Open,
Test Conditions
IN
IN
= GND or V
= 3.4V, f = 0
4
Min
CC
⎯
1.5
1.5
(1)
.
, f = 0
(1)
Typ.
⎯
⎯
⎯
INDUSTRIAL TEMPERATURE RANGE
Typ.
0.2
⎯
⎯
(2)
0.25
Max.
6.5
5.5
(3)
Max.
0.25
2.5
3
mA/MHz
Unit
Unit
mA
μA
ns
ns
ns