ISP1104W STEricsson, ISP1104W Datasheet - Page 5

• Manufacturer Part Number: ISP1104W
• Manufacturer: STEricsson

Specifications of ISP1104W

• Lead Free Status / RoHS Status: Supplier Unconfirmed

Philips Semiconductors
9397 750 11229
Product data
Table 2:
[1]
Symbol
SUSPND
MODE
V
VBUSDET
D
D
VPO/VO
VMO/FSE0
V
V
V
SOFTCON
GND
CC(I/O)
reg(3.3)
CC(5.0)
pu(3.3)
Symbol names with an overscore (for example, NAME) indicate active LOW signals.
[1]
Pin description
Pin
5
6
7
8
9
10
11
12
13
14
15
16
exposed
die pad
Rev. 02 — 14 October 2003
Type
I
I
-
O
AI/O
AI/O
I
I
-
-
-
I
-
…continued
Description
suspend input (CMOS level with respect to V
HIGH level enables low-power state while the USB bus is
inactive and drives output RCV to a LOW level
input pad; push pull; CMOS
mode input (CMOS level with respect to V
level enables the differential input mode (pins VPO and
VMO) whereas a LOW level enables a single-ended input
mode (pins VO and FSE0); see
input pad; push pull; CMOS
supply voltage for digital I/O pins (1.65 V to 3.6 V); when
V
three-state; this supply pin is totally independent of
V
voltage
V
V
when V
output pad; push pull; 4 mA output drive; CMOS
negative USB data bus connection (analog, differential)
positive USB data bus connection (analog, differential);
connect a 1.5 k resistor to pin V
driver data input (CMOS level with respect to V
Schmitt trigger); see
input pad; push pull; CMOS
driver data input (CMOS level with respect to V
Schmitt trigger); see
input pad; push pull; CMOS
regulated supply voltage output (3.0 V to 3.6 V); a
decoupling capacitor of at least 0.1 F is required
supply voltage input (4.0 V to 5.5 V); can be connected
directly to the USB supply line V
pull-up supply voltage (3.3 V
1.5 k resistor on pin D (full-speed); pin function is
controlled by input SOFTCON
SOFTCON = LOW — V
ensures zero pull-up current
SOFTCON = HIGH — V
connected to V
software controlled USB connection input; a HIGH level
applies 3.3 V to pin V
external 1.5 k pull-up resistor; this allows USB connect
or disconnect signalling to be controlled by software
input pad; push pull; CMOS
ground supply; down bonded to the exposed die pad
(heatsink); to be connected to the PCB ground
CC(I/O)
CC(5.0)
BUS
CC(I/O)
indicator output (CMOS level with respect to
); when V
BUS
is not connected, the pins D and D are in
and V
< 3.6 V, then VBUSDET = LOW
reg(3.3)
reg(3.3)
BUS
and must never exceed the V
> 4.1 V, then VBUSDET = HIGH and
Table 4
Table 4
pu(3.3)
pu(3.3)
© Koninklijke Philips Electronics N.V. 2003. All rights reserved.
pu(3.3)
Advanced USB transceiver
, which is connected to an
and
and
floating (high impedance);
= 3.3 V; internally
10 %); connect an external
Table 4
BUS
Table 5
Table 5
pu(3.3)
ISP1104
and
CC(I/O)
Table 5
CC(I/O)
CC(I/O)
CC(I/O)
); a HIGH
reg(3.3)
); a
4 of 19
,
,