M27C4001-15C1TR STMicroelectronics, M27C4001-15C1TR Datasheet
M27C4001-15C1TR
Specifications of M27C4001-15C1TR
Related parts for M27C4001-15C1TR
M27C4001-15C1TR Summary of contents
Page 1
... ELECTRONIC SIGNATURE – Manufacturer Code: 20h – Device Code: 41h DESCRIPTION The M27C4001 Mbit EPROM offered in the two ranges UV (ultra violet erase) and OTP (one time programmable ideally suited for micro- processor systems requiring large programs and is organised as 524,288 by 8 bits. ...
Page 2
... A16 A15 A12 2/17 Figure 2B. LCC Connections A18 30 A17 29 A14 28 A13 A11 A10 Table 1. Signal Names A0-A18 Q0- A10 AI01155B M27C4001 AI00723 Address Inputs Data Outputs Chip Enable Output Enable Program Supply Supply Voltage Ground A14 A13 A8 A9 A11 G A10 E Q7 ...
Page 3
... Table 4. Electronic Signature Identifier A0 V Manufacturer’s Code IL Electronic Signature V IH (1) Parameter (3) +2V for a period less than 20ns Pulse M27C4001 Value –40 to 125 –50 to 125 –65 to 150 – – –2 to 13.5 – Data Out Data Out Unit °C °C °C ...
Page 4
... Standby Mode The M27C4001 has a standby mode which reduc- es the supply current from 30mA to 100 A. The M27C4001 is placed in the standby mode by ap- plying a CMOS high signal to the E input. When in the standby mode, the outputs are in a high imped- ance state, independent of the G input. ...
Page 5
... M27C4001 = Min Max ±10 ± 100 10 –0.3 0 0.4 2.4 V – 0. M27C4001 (3) (3) (3) -45 -55 Max Min Max Min Max Unit A ...
Page 6
... F bulk electrolytic capacitor should be used between V es. The bulk capacitor should be located near the power supply connection point. The purpose of the bulk capacitor is to overcome the voltage drop caused by the inductive effects of PCB traces M27C4001 -70 -80/-90 -10/-12/-15 Max Min Max Min 70 80 ...
Page 7
... Sampled only, not 100% tested. Programming When delivered (and after each erasure for UV EPROM), all bits of the M27C4001 are in the ’1’ state. Data is introduced by selectively program- ming ’0’s into the desired bit locations. Although only ’0’s will be programmed, both ’1’s and ’0’s can be present in the data word. The only way to change a ’ ...
Page 8
... Ex- cept for E, all like inputs including G of the parallel M27C4001 may be common. A TTL low level pulse applied to a M27C4001’s E input, with V at 12.75V, will program that M27C4001. A high level E input inhibits the other M27C4001s from being programmed ...
Page 9
... M27C4001 in about 3 years, while it would take approximately 1 week to cause erasure when exposed to direct sunlight. If the M27C4001 exposed to these types of lighting conditions for extended pe- riods of time suggested that opaque labels ...
Page 10
... Options X = Additional Burn- Tape & Reel Packing Note: 1. High Speed, see AC Characteristics section for further information. For a list of available options (Speed, Package, etc...) or for further information on any aspect of this de- vice, please contact the STMicroelectronics Sales Office nearest to you. 10/17 M27C4001 - ...
Page 11
... Table 12. Revision History Date July 1998 First Issue 09/25/00 AN620 Reference removed 11/29/00 PLCC codification changed (Table 11) Revision Details M27C4001 11/17 ...
Page 12
... M27C4001 Table 13. FDIP32W - 32 pin Ceramic Frit-seal DIP with window, Package Mechanical Data Symbol Typ 1. 38.10 E 15. 2.54 eA 14. Ø 7.11 N Figure 8. FDIP32W - 32 pin Ceramic Frit-seal DIP with window, Package Outline Drawing is not to scale. 12/17 millimeters Min Max 5.72 0.51 1.40 3.91 4 ...
Page 13
... M27C4001 inches Typ Min – 0.015 0.140 0.015 0.060 – 0.008 1.645 1.500 – 0.600 – 0.535 0.100 – 0.600 – 0.600 0.125 0.070 0° ...
Page 14
... M27C4001 Table 15. LCCC32W - 32 lead Leadless Ceramic Chip Carrier, Package Mechanical Data Symbol Typ 1. 7.62 e3 10.16 h 1. Figure 10. LCCC32W - 32 lead Leadless Ceramic Chip Carrier, Package Outline LCCCW-a Drawing is not to scale. 14/17 millimeters Min Max 2.80 0.51 0.71 11.53 11.63 13.72 14.22 – ...
Page 15
... 0.51 (.020) R M27C4001 inches Typ Min 0.100 0.060 0.015 0.013 0.026 0.485 0.447 0.390 0.050 0.585 0.547 0.490 0.000 0.035 D2/E2 B 1.14 (.045) ...
Page 16
... M27C4001 Table 17. TSOP32 - 32 lead Plastic Thin Small Outline mm, Package Mechanical Data Symbol Typ 0. Figure 12. TSOP32 - 32 lead Plastic Thin Small Outline mm, Package Outline 1 N/2 TSOP-a Drawing is not to scale. 16/17 millimeters Min Max 1.20 0.05 0.17 0.95 1.05 0.15 0.27 0.10 0.21 19.80 20 ...
Page 17
... Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A. The ST logo is registered trademark of STMicroelectronics All other names are the property of their respective owners 2000 STMicroelectronics - All Rights Reserved STMicroelectronics GROUP OF COMPANIES www.st.com M27C4001 17/17 ...