SLFDM44H-064J STEC, SLFDM44H-064J Datasheet - Page 21

• Manufacturer Part Number: SLFDM44H-064J
• Manufacturer: STEC
• Type: Flash Diskr

Specifications of SLFDM44H-064J

• Density: 64MByte
• Operating Supply Voltage (typ): 3.3/5V
• Operating Temperature (min): 0C
• Operating Temperature (max): 70C
• Package Type: Not Required
• Mounting: Surface Mount
• Pin Count: 44
• Operating Temperature Classification: Commercial
• Operating Supply Voltage (min): 3.18/4.75V
• Operating Supply Voltage (max): 3.465/5.25V
• Programmable: Yes
• Lead Free Status / RoHS Status: Not Compliant

Request Sense
(code: 03h)
This command requests an extended error code after a
command ends with an error. Refer to table below.
Code
00H
01H
09H
20H
21H
2FH
35H, 36H
11H
18H
05H, 30H-34H, 37H, 3EH
10H, 14H
3AH
1FH
0CH, 38H, 3BH, 3CH, 3FH
03H
22H
Seek
(code: 7Xh)
This command is effectively a NOP command to the Card
although it does perform a range check.
Set Features
(code: EFh)
This command is used by the host to establish or select
certain features.
SimpleTech P/N:
(where p=connector; q=LP if low profile; r=plug-in and housing;
U=RoHS compliant lead-free; I=Ind. Op. Temp)
Feature
CCH
BBH
01H
55H
66H
81H
SLFDMpqr-064J(U)(I)
Enable 8-bit data transfers
Disable Read Look Ahead
Disable Power on Reset (POR)
establishment of defaults at Soft
Reset
Disable 8-bit data transfers
4bytes of data apply on Read/Write
Long commands
Enable Power on Reset (POR)
establishment of default at Soft
Reset
Description
No error detected
Self test OK (No error)
Miscellaneous Error - N/A
Invalid Command
Invalid Address (requested
Head or Sector invalid)
Address Overflow (address
too large)
Supply or generate Voltage
Out of Tolerance
Uncorrectable ECC Error
Correctable ECC Error - N/A
Self Test Diagnostic Failed
ID Not Found - N/A
Spare Sectors Exhausted
Data Transfer Error / Aborted
Command
Corrupted Media Format - N/A
Write / Erase Failed - N/A
Power Level 1 Disabled
Description
Document Part Number 61000-02832-314 July 2005
Set Multiple Mode
(code: C6h)
This command enables the module to perform Read and
Write Multiple operations and establishes the block count
for these commands.
Set Sleep Mode
(code: E6h or 99h)
This is the only command that allows the host to set the
module into Sleep mode. When the module is set to sleep
mode, the module clears the BSY line and issues an
interrupt. The module enters sleep mode and the only
method to make the module active again (back to normal
operation) is by performing a hardware reset or a
software reset.
Stand By
(code: E2h or 96h)
This command is sets the module in Standby mode. If the
Sector Count Register is a value other than 0H, an Auto
Power Down is enabled and when the module returns to
the idle mode, the timer starts a countdown. The time is
set in the Sector Count Register.
Stand By Immediate
(code: E0h or 94h)
This command causes the module to set BSY, enter the
Standby mode, clear BSY and return the interrupt
immediately.
Translate Sector
(code: 87h)
This command allows the host a method of determining
the exact number of times a user sector has been erased
and programmed. This command is not supported.
Wear Level
(code: F5h)
This command is effectively a NOP command and only
implemented for backward compatibility. The Sector Count
Register will always be returned with an 00h indicating
Wear Level is not needed.
Write Buffer
(code: E8h)
This command enables the host to overwrite the contents
of the module’s sector buffer with any data pattern
desired.
Write Long Sector
(code: 32h or 33h)
This command is provided for compatibility purposes and
is similar to the Write Sector(s) command except that it
writes 516 bytes instead of 512 bytes.
FLASH DISK MODULE
Page 21