M48T35AV-10MH6TR STMicroelectronics, M48T35AV-10MH6TR Datasheet - Page 14

• Manufacturer Part Number: M48T35AV-10MH6TR
• Manufacturer: STMicroelectronics
• Type: NVSRAMr

Specifications of M48T35AV-10MH6TR

• Word Size: 8b
• Organization: 32Kx8
• Density: 256Kb
• Interface Type: Parallel
• Access Time (max): 100ns
• Operating Supply Voltage (typ): 3.3V
• Package Type: SOH
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 3V
• Operating Temp Range: -40C to 85C
• Pin Count: 28
• Mounting: Surface Mount
• Supply Current: 30mA
• Lead Free Status / RoHS Status: Not Compliant

Clock operations
Note:
3.4
14/29
Table 5.
Keys:
When CEB is set to '1,' CB will toggle from '0' to '1' or from '1' to '0' at the turn of the century
(dependent upon the initial value set).
When CEB is set to '0,' CB will not toggle. The WRITE bit does not need to be set to write to
CEB.
Calibrating the clock
The M48T35AV is driven by a quartz-controlled oscillator with a nominal frequency of
32,768 Hz. The devices are tested not to exceed 35 ppm (parts per million) oscillator
frequency error at 25°C, which equates to about ±1.53 minutes per month. With the
calibration bits properly set, the accuracy of each M48T35AV improves to better than
+1/–2 ppm at 25°C.
The oscillation rate of any crystal changes with temperature (see
Most clock chips compensate for crystal frequency and temperature shift error with
cumbersome “trim” capacitors. The M48T35AV design, however, employs periodic counter
correction. The calibration circuit adds or subtracts counts from the oscillator divider circuit
at the divide by 256 stage, as shown in
are blanked (subtracted, negative calibration) or split (added, positive calibration) depends
upon the value loaded into the five calibration bits found in the control register. Adding
counts speeds the clock up, subtracting counts slows the clock down.
The calibration byte occupies the five lower order bits (D4-D0) in the control register 7FF8h.
These bits can be set to represent any value between 0 and 31 in binary form. Bit D5 is the
SIGN bit; '1' indicates positive calibration, '0' indicates negative calibration. Calibration
Address
7FFDh
7FFCh
7FFFh
7FFEh
7FFBh
7FFAh
7FF9h
7FF8h
S = SIGN bit
FT = FREQUENCY TEST bit (must be set to '0' upon power for normal operation)
R = READ bit
W = WRITE bit
ST = STOP bit
0 = Must be set to '0'
CEB = CENTURY ENABLE bit
CB = CENTURY bit
D7
ST
W
Register map
0
0
0
0
0
D6
FT
R
0
0
10 years
0
10 seconds
10 minutes
CEB
D5
S
0
10 hours
10 date
Doc ID 6845 Rev 8
10 M.
CB
D4
Data
D3
Figure 10 on page
0
Calibration
D2
Seconds
Minutes
Month
Hours
Date
Year
Day
D1
16. The number of times pulses
D0
Figure 9 on page
Century/day
Seconds
Minutes
Control
Month
Hours
Date
Year
Function/range
BCD format
00-01/01-07
M48T35AV
00-99
01-12
01-31
00-23
00-59
00-59
16).