T2526N036-DDW Atmel, T2526N036-DDW Datasheet
T2526N036-DDW
Specifications of T2526N036-DDW
Related parts for T2526N036-DDW
T2526N036-DDW Summary of contents
Page 1
Features • No External Components Except PIN Diode • Supply-voltage Range: 2.7V to 5.5V • Highest Sensitivity Due to Automatic Sensitivity Adaption (AGC) and Automatic Strong Signal Adaption (ATC) • Automatic Supply Voltage Adaptation • Highest Immunity against Disturbances from ...
Page 2
Figure 1-1. Block Diagram IN Carrier frequency f 0 Modulated IR signal min pulses T2526 2 VS CGA and Input filter AGC/ATC Oscillator and digital control GND OUT Micro- Demodulator controller T2526 4597I–AUTO–05/10 ...
Page 3
Pin Description Table 2-1. Pin Description Symbol Function VS Supply voltage OUT Data output IN Input PIN-diode GND Ground 3. Absolute Maximum Ratings Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This ...
Page 4
Electrical Characteristics, 3-V Operation T = 25° unless otherwise specified. amb S No. Parameters 1 Supply 1.1 Supply-voltage range 1.2 Supply current 2 Output (1) 2.1 Internal pull-up resistor 2.2 Output voltage low 2.3 Output voltage ...
Page 5
Electrical Characteristics, 3-V Operation (Continued 25° unless otherwise specified. amb S No. Parameters 4 Controlled Amplifier and Filter Maximum value of variable 4.1 gain (CGA) Minimum value of variable 4.2 gain (CGA) (3) 4.3 ...
Page 6
Electrical Characteristics, 5-V Operation (Continued 25° unless otherwise specified. amb S No. Parameters 7 Input 7.1 Input DC current Input DC-current 7.2 See Figure 6-4 on page 8 Min. detection threshold 7.3 current See ...
Page 7
Typical Electrical Curves at T Figure 6-1. Figure 6-2. Figure 6-3. 4597I–AUTO–05/10 = 25°C amb I versus Eemin IN_DC S 100 0.1 0.1 1 ...
Page 8
Figure 6-4. Figure 6-5. Figure 6-6. T2526 8 V versus IN_DC S 3.5 3.0 2.5 2.0 1.5 1 IN_DC Data Transmission Rate ...
Page 9
Figure 6- f/f Example 1/(1.047 – 0.954 Figure 6-8. Illustration of Used Terms Example kHz, burst with 16 pulses, 16 periods 1066 µs 533 µ OUT DON ...
Page 10
Figure 6-9. Test Circuit IN_AC100 PULSE f Figure 6-10. Application Circuit 220 4.7 µF IN_DC T2526 10 ...
Page 11
Chip Dimensions Figure 7-1. Note: Dimensions Pad metallurgy Finish Note: 4597I–AUTO–05/10 Chip Size in µm GND 336,906 VS 55,652 T2526 55,62 OUT 0,0 Pad coordinates are given for lower left corner of the pad in µm from the origin ...
Page 12
Ordering Information Delivery: unsawn wafers (DDW) in box Extended Type (2) Number PL (1) T2526S0xx C-DDW 2 (1) T2526S1xx C-DDW 1 (1) T2526S2xx C-DDW 2 (1) T2526S3xx C-DDW 1 (1) T2526S6xx C-DDW 2 (1) T2526S7xx C-DDW 1 Notes: 1. ...
Page 13
Revision History Please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this document. Revision No. 4597I-AUTO-05/10 4597H-AUTO-09/09 4597G-AUTO-10/06 4597F-AUTO-04/06 4597E-AUTO-04/06 4597D-AUTO-08/05 4597I–AUTO–05/10 History • Features on page 1 ...
Page 14
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...