BTS410E2E3062ANT Infineon Technologies, BTS410E2E3062ANT Datasheet
BTS410E2E3062ANT
Specifications of BTS410E2E3062ANT
Related parts for BTS410E2E3062ANT
BTS410E2E3062ANT Summary of contents
Page 1
... Electrostatic discharge (ESD) protection Application C compatible power switch with diagnostic feedback for 12 V and grounded loads All types of resistive, inductive and capacitve loads Replaces electromechanical relays, fuses and discrete circuits General Description N channel vertical power FET with charge pump, ground referenced CMOS compatible input and diagnostic feedback, monolithically integrated in Smart SIPMOS technology ...
Page 2
... Device on 50mm*50mm*1.5mm epoxy PCB FR4 with 6cm connection. PCB is vertical without blown air. Semiconductor Group Function Logic ground Input, activates the power switch in case of logical high signal Positive power supply voltage, the tab is shorted to this pin Diagnostic feedback, low on failure Output to the load ...
Page 3
... Electrical Characteristics Parameter and Conditions ° unless otherwise specified j bb Load Switching Capabilities and Characteristics On-state resistance (pin 1 Nominal load current, ISO Norm (pin 0 ° Output current (pin ) while GND disconnected or 5 GND pulled up page 7, T =-40...+150°C j Turn-on time ...
Page 4
... Repetitive overload shutdown current limit (see timing diagrams, page 11 Short circuit shutdown delay after input pos. slope V > ON(SC) min value valid only, if input "low" time exceeds 60 s Output clamp (inductive load switch off mA OUT bb ON(CL Short circuit shutdown detection voltage (pin ...
Page 5
Parameter and Conditions ° unless otherwise specified j bb Input and Status Feedback Input turn-on threshold voltage Input turn-off threshold voltage Input threshold hysteresis Off state input current (pin 2 ...
Page 6
Truth Table Input- Output level level Normal L L operation H H Open load Short circuit GND H L Short circuit Overtem perature ...
Page 7
Status output R ST(ON) GND ESD-Zener diode typ., max 5 mA; R < 250 at 1.6 mA, ESD zener diodes are not ST(ON used as voltage clamp at DC conditions. Operation in this mode may result ...
Page 8
... Semiconductor Group Inductive Load switch-off energy dissipation E bb OUT 5 = Energy stored in load inductance: While demagnetizing load inductance, the energy dissipated in PROFET is E OUT with an approximate solution for Maximum allowable load inductance for a single switch off [mH] 10000 1000 D 100 BTS 410 OUT ...
Page 9
Typ. transient thermal impedance chip case Z = f(t , D), D=t /T thJC [K/W] thJC 10 1 0.1 0.01 1E-5 1E-4 1E-3 1E-2 Semiconductor Group D= 0.5 0.2 0.1 0.05 0.02 0.01 0 1E-1 1E0 1E1 ...
Page 10
... Options Overview all versions: High-side switch, Input protection, ESD protection, load dump and reverse battery protection with 150 ground Type Logic version Overtemperature protection with hysteresis T j >150 °C, latch function >150 °C, with auto-restart on cooling Short circuit to GND protection switches off when V > ...
Page 11
... ST open drain A in case of too early V IN =high the device may not turn on (curve A) t approx. 150 s d(bb IN) Figure 2a: Switching a lamp OUT I L Semiconductor Group Figure 2b: Switching an inductive load IN t d(ST OUT L(OL the time constant of load is too large, open-load-status may ...
Page 12
Figure 3b: Turn on into overload L(SCp) I L(SCr) ST Heating up may require several seconds < 8.5 V typ. bb OUT Figure 3c: Short circuit while on OUT I ...
Page 13
Figure 5b: Open load: detection in ON-state, open load occurs in on-state IN t d(ST OL1 OUT normal open tbd s typ tbd s typ d(ST OL1) d(ST OL2) Figure 6a: Undervoltage: ...
Page 14
Figure 9a: Overvoltage at short circuit shutdown bb(o rst) Output short to GND V OUT short circuit shutdown Overvoltage due to power line inductance. No overvoltage auto- restart of PROFET after short circuit ...
Page 15
Package and Ordering Code All dimensions in mm Standard TO-220AB/5 BTS 410 E2 Q67060-S6102-A2 TO-220AB/5, Option E3043 BTS 410 E2 E3043 Q67060-S6102-A3 Semiconductor Group SMD TO-220AB/5, Opt. E3062 Ordering code BTS410E2 E3062A T&R: Changed since 04.96 Date Change Mar. E ...
Page 16
... Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies Office. Infineon Technologies Components may only be used in life- support devices or systems with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system affect the safety or effectiveness of that device or system ...