ACS704ELC-015 Allegro Microsystems Inc, ACS704ELC-015 Datasheet - Page 2

• Manufacturer Part Number: ACS704ELC-015
• Description: SENSOR CURRENT 15A 5V BI 8-SOIC
• Manufacturer: Allegro Microsystems Inc
• Series: -r

Specifications of ACS704ELC-015

• Operating Supply Voltage (min): 4.5V
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Output Current: 10mA
• Package Type: SOIC
• Pin Count: 8
• Mounting: Surface Mount
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Current - Sensing: ±15A
• Accuracy: ±1%
• Sensitivity: 133mV/A
• Current - Supply: 8mA
• Sensor Type: Hall Effect
• Voltage - Supply: 4.5 V ~ 5.5 V
• Output: 2.5V
• Frequency: 50kHz
• Response Time: 8µs
• Polarization: Bidirectional
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (0.154", 3.90mm Width)
• Lead Free Status / RoHS Status: Compliant

ACS704ELC015-DS, Rev. 7
Supply Voltage, V
Reverse Supply Voltage, V
Output Voltage, V
Reverse Output Voltage, V
Output Current Source, I
Output Current Sink, I
Operating Temperature,
Storage Temperature, T
Nominal Operating Temperature, T
Overcurrent Transient Tolerance*, I
*
1 pulse every 100 seconds.
100 total pulses, 250 ms duration each, applied at a rate of
Pin 1: IP+
AB SO LUTE MAX I MUM RAT INGS
Pin 2: IP+
Pins 6 and 7 are internally connected in shipping
product. For compatibility with future devices,
leave pin 6 floating.
Maximum Junction, T
Pin 3: IP–
Range E ............................................ –40 to 85ºC
Pin 4: IP–
with Voltage Isolation and a Low-Resistance Current Conductor
Fully Integrated, Hall Effect-Based Linear Current Sensor IC
OUT
CC
Package LC
.......................................... 16 V
........................................ 16 V
OUT(Sink)
S
OUT(Source)
...................... –65 to 170°C
TÜV America
Certificate Number:
U8V 04 12 54214 005
J(max)
ROUT
RCC
........................ –16 V
.......................10 mA
....................... 165°C
...................... –0.1 V
A
................. 3 mA
P
Pin 8: VCC
................ 60 A
Pin 7: VOUT
Pin 6: N.C.
Pin 5: GND
ACS704ELC-015
The Allegro ACS704 family of current sensor ICs provides economical and
precise solutions for current sensing in industrial, automotive, commercial, and
communications systems. The device package allows for easy implementation
by the customer. Typical applications include motor control, load detection and
management, switched-mode power supplies, and overcurrent fault protection.
The device consists of a precision, low-offset linear Hall circuit with a copper
conduction path located near the surface of the die. Applied current flowing
through this copper conduction path generates a magnetic field which the
integrated Hall IC converts into a proportional voltage. Device accuracy is
optimized through the close proximity of the magnetic signal to the Hall
transducer. A precise, proportional voltage is provided by the low-offset, chopper-
stabilized BiCMOS Hall IC, which is programmed for accuracy at the factory.
The output of the device has a positive slope (>V
current flows through the primary copper conduction path (from pins 1 and
2, to pins 3 and 4), which is the path used for current sampling. The internal
resistance of this conductive path is typically 1.5 mΩ, providing low power loss.
The thickness of the copper conductor allows survival of the device at up to 3×
overcurrent conditions. The terminals of the conductive path are electrically
isolated from the signal leads (pins 5 through 8). This allows the ACS704 to be
used in applications requiring electrical isolation without the use of opto-isolators
or other costly isolation techniques.
The ACS704 is provided in a small, surface mount SOIC8 package. The leadframe
is plated with 100% matte tin, which is compatible with standard lead (Pb) free
printed circuit board assembly processes. Internally, the flip-chip uses high-tem-
perature Pb-based solder balls, currently exempt from RoHS. The device is fully
calibrated prior to shipment from the factory.
Features and Benefits
• Small footprint, low-profile SOIC8 package
• 1.5 mΩ internal conductor resistance
• 800 V
• 4.5 to 5.5 V, single supply operation
• 50 kHz bandwidth
• 100 mV/A output sensitivity and 20 A dynamic range
• Output voltage proportional to ac and dc currents
• Factory-trimmed for accuracy
• Extremely stable output offset voltage
• Near-zero magnetic hysteresis
• Ratiometric output from supply voltage
Use the following complete part number when ordering:
RMS
minimum isolation voltage between pins 1-4 and 5-8
ACS704ELC-015
Part Number
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 [phone]
www.allegromicro.com
SOIC8 surface mount
CC
Package
/ 2) when an increasing