SLFDM44LPH-256J STEC, SLFDM44LPH-256J Datasheet - Page 22

• Manufacturer Part Number: SLFDM44LPH-256J
• Manufacturer: STEC
• Type: Flash Diskr

Specifications of SLFDM44LPH-256J

• Density: 256MByte
• Operating Supply Voltage (typ): 5V
• Operating Temperature (min): 0C
• Operating Temperature (max): 70C
• Package Type: Not Required
• Mounting: Screw
• Pin Count: 44
• Operating Temperature Classification: Commercial
• Operating Supply Voltage (min): 4.75V
• Operating Supply Voltage (max): 5.25V
• Programmable: Yes
• Lead Free Status / RoHS Status: Not Compliant

SLFDM(40/44)(LP)(V/H)-xxxJ(I)
REVISION HISTORY
Rev. Change Description from Previous Revision
-101 3/1/04. Initial Release.
-102 5/26/04. General Description updated with new
-103 5/27/04. Missing dimension values added to Package
-104 7/2/04. Pin Description changes: -IOIS16 not used in
-105 7/9/04. Endurance increased from 300,000 cycles min
SimpleTech Inc. reserves the right to make changes to specifications and product descriptions such as but not limited to numbers, parameters
and other technical information contained herein without notice. Contact SimpleTech Inc. sales office to obtain the latest specifications.
SimpleTech Inc. grants no warranty with respect to this Data Sheet, neither explicit nor implied, and it is not liable for direct or indirect
damages. Some States do not grant the exclusion of incidental damages and as such this statement may not be valid in such states. The
provisions of this Data Sheet do not convey to the purchaser of the device any license under any patent rights or other intellectual property
rights of SimpleTech Inc. or others.
marketing copy. R/W speeds changed from
5.4/4.5MB/s to 5/5MB/s. 32MB, 64MB, 3GB, and 4GB
versions removed. CHS Parameter table added. VCC
5V tolerance changed to 5% from 10%. Preliminary
notice removed except for environmental
specifications. WP jumper added to Dimensions.
Disclaimer notice added.
Dimensions, 40-pin horizontal plug-in.
IDE mode; -IORDY description corrected to not used
by card and pulled up by 4.7K ohm resistor.
Performance rates for read and write described as
sustained read and sustained write. Error register bit 0
Function “not supported” phrase removed. DMA
commands removed (paper only error indicated that
DMA was supported). Identify Drive Information table
updated to reflect DMA not supported. DC
Characterists Sleep Mode value changed from 120uA
to 1200uA for 5V power supply.
to 2 million cycles min.
Document Part Number 61000-02832-113 March 2005
-106 7/22/04. “up to” added to sustained read and write
-107 7/27/04 SLFDM44LPH-xxxJ(I) dimensions corrected
-108 7/30/04. P/N SLFDM44LPH-xxxJ(I) corrected to
-109 8/23/04. WP Jumper labeled “Optional.” Tolerance of
-110 10/21/04. Master/Slave jumpers corrected on
-111 10/29/04. Standard ECC, Endurance, and Warranty
-112 2/16/05. Shock parameter of 11ms corrected to 0.330
-113 3/3/05. Humidity parameter changed to 95% from
data rate performance.
to released product. Ordering Information made easy
to read.
SLFDM44H-xxxJ(I).
connector protrusion in SLFLD40LPV-xxxJ(I)
dimensions changed from 0.005 to 0.050.
Environmental Characteristics updated to testing
parameters. Definition for Serial #, Firmware Rev., and
Model # in the Identify Drive Information table added
in callout. Words 0, 4-5, 20-21, 49, and 63 in Drive ID
table corrected. SLFLD44V-xxxJ(I) flash disk module
added.
dimension illustrations.
bullets added to Features on page 1.
to 0.750ms. WP jumpering removed.
85%.
FLASH DISK MODULE
Page 22