SY100E111JC Micrel Inc, SY100E111JC Datasheet - Page 3

• Manufacturer Part Number: SY100E111JC
• Description: IC CLOCK DRIVER 1:9 DIFF 28-PLCC
• Manufacturer: Micrel Inc
• Series: 100E, ECLinPS™r
• Type: Fanout Buffer (Distribution)r

Specifications of SY100E111JC

• Number Of Circuits: 1
• Ratio - Input:output: 1:9
• Differential - Input:output: Yes/Yes
• Input: PECL
• Output: PECL
• Voltage - Supply: 4.2 V ~ 5.5 V
• Operating Temperature: 0°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 28-LCC (J-Lead)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Frequency-max: -

Micrel, Inc.
V
V
Notes:
1. The differential propagation delay is defined as the delay from the crossing points of the differential input signals to the crossing point of the differential
2. The single-ended propagation delay is defined as the delay from the 50% point of the input signal to the 50% point of the output signal.
3. Enable is defined as the propagation delay from the 50% point of a negative transition on /EN to the 50% point of a positive transition on Q (or a negative
4. The within-device skew is defined as the worst case difference between any two similar delay paths within a single device.
5. The set-up time is the minimum time that /EN must be asserted prior to the next transition of /IN/IN to prevent an output response greater than 75mV
6. The hold time is the minimum time that /EN must remain asserted after a negative going IN or a positive going /IN to prevent an output response greater
7. The release time is the minimum time that /EN must be de-asserted prior to the next IN, /IN transition to ensure an output response that meets the specified
8. V
9. V
M9999-032006
[e-mail] or [phone]
Symbol
V
I
I
Symbol
t
t
t
t
t
V
V
t
t
EE
EE
IH
EE
PD
SKEW
S
H
R
r
f
AC ELECTRICAL CHARACTERISTICS
DC ELECTRICAL CHARACTERISTICS
BB
PP
CMR
output signals.
transition on /Q). Disable is defined as the propagation delay from the 50% point of a positive transition on /EN to the 50% point of a negative transition
on Q (or a positive transition on /Q).
to that /IN/IN transition (see Figure 1).
than 75mV to that IN, /IN transition (see Figure 2).
IN to Q propagation delay and output transition times (see Figure 3).
E111, as a differential input as low as 50mV will still produce full ECL levels at the output.
such that the peak-to-peak voltage is less than 1.0V and greater than or equal to V
PP
CMR
= V
= V
(min.) is defined as the minimum input differential voltage which will cause no increase in the propagation delay. The V
is defined as the range within which the V
EE
EE
(Min.) to V
(Min.) to V
Output Reference
Voltage
Input HIGH Current
Power Supply
Current
Propagation Delay to
Output
Within-Device Skew
Set-up Time
Hold Time
Release Time
Minimum Input Swing
Common Mode Range
Rise/Fall Times
(20% to 80%)
IN (differential)
IN (single-ended)
Enable
Disable
/EN to IN
IN to /EN
/EN to IN
Parameter
Parameter
(3)
(3)
EE
EE
(5)
(6)
(7)
(Max.); V
(Max.); V
100E
100E
(1)
10E
10E
(2)
(4)
(8)
(9)
CC
CC
Min.
= V
= V
Min.
T
A
CCO
CCO
IH
T
= –40 C
Typ.
level may vary, with the device still meeting the propagation delay specification. The V
A
Typ.
= –40 C
= GND
= GND
Max.
Max.
–1.38
–1.38
Min.
—
—
—
Min.
–1.6
430
330
450
450
200
300
250
275
—
0
T
3
A
T
Typ.
A
= 0 C
—
—
—
48
48
–200
Typ.
100
375
= 0 C
25
—
—
—
—
—
—
0
–1.27 –1.35
–1.26 –1.38
Max.
PP
150
60
60
Max.
–0.4
630
730
850
850
600
(min.).
50
—
—
—
—
Min.
—
—
—
Min.
–1.6
430
330
450
450
200
300
250
275
—
0
T
A
T
= +25 C
Typ.
A
48
48
—
—
—
–200
= +25 C
Typ.
100
375
25
—
—
—
—
—
—
0
–1.25 –1.31
–1.26 –1.38
Max.
150
60
60
Max.
–0.4
600
630
730
850
850
50
—
—
—
—
Min.
—
—
—
Min.
–1.6
430
330
450
450
200
300
250
275
—
0
T
PP
A
T
(min.) is AC limited for the
A
= +85 C
Typ.
—
—
—
48
55
= +85 C
–200
Typ.
100
375
25
—
—
—
—
—
—
0
–1.19
–1.26
Max.
150
60
69
IL
Max. Unit
–0.4
630
730
850
850
600
SY100E111
50
level must be
—
—
—
—
SY10E111
Unit
mA
mV
V
ps
ps
ps
ps
ps
ps
A
V