MCP4922-E/P Microchip Technology, MCP4922-E/P Datasheet
MCP4922-E/P
Specifications of MCP4922-E/P
Available stocks
Related parts for MCP4922-E/P
MCP4922-E/P Summary of contents
Page 1
... OUTB SHDN 2004 Microchip Technology Inc. MCP4921/4922 Description The Microchip Technology Inc. MCP492X are 2.7 – 5.5V, low-power, low DNL, 12-Bit Digital-to-Analog Con- verters (DACs) with optional 2x buffered output and SPI interface. The MCP492X are DACs that provide high accuracy ...
Page 2
... Electrical Specifications: Unless otherwise indicated GND 100 -40 to +85°C. Typical values at +25° Parameters Sym Power Requirements Input Voltage V DD Input Current - MCP4921 I DD Input Current - MCP4922 Hardware Shutdown Current I SHDN Software Shutdown Current I SHDN_SW Power-on-Reset Threshold V POR DC Accuracy Resolution n INL Error INL DNL ...
Page 3
... GND 100 -40 to +85°C. Typical values at 25° Parameters Sym Power Requirements Input Voltage V DD Input Current - MCP4921 I DD Input Current - MCP4922 Hardware Shutdown Current I SHDN Software Shutdown Current I SHDN_SW Power-On Reset threshold V POR DC Accuracy Resolution n INL Error INL DNL DNL ...
Page 4
... Electrical Specifications: Unless otherwise indicated GND 100 pF. Typical values at +125°C by characterization or simulation. L Parameters Sym Power Requirements Input Voltage V DD Input Current - MCP4921 I DD Input Current - MCP4922 Hardware Shutdown Current I SHDN Software Shutdown Current I SHDN_SW Power-On Reset threshold V POR DC Accuracy Resolution n INL Error ...
Page 5
... Settling Time t settling Dynamic Performance DAC to DAC Crosstalk Major Code Transition Glitch Digital Feedthrough Analog Crosstalk Note 1: By design, not production tested. 2: Too small to quantify. 2004 Microchip Technology Inc. MCP4921/4922 = 5V 0V 2.048V, output buffer gain ( REF Min Typ Max Units — ...
Page 6
... MHz (Note 1) cLK = +25°C (Note Note 1 ns Note 1 ns Applies only when CS falls with CLK high. (Note 1) ns Note 1 ns Note 1 ns Note 1 ns Note 1 ns Note 1 ns Note 1 ns Note 1 t CSH t IDLE t CHS LSB 2004 Microchip Technology Inc. ...
Page 7
... Thermal Resistance, 14L-PDIP Thermal Resistance, 14L-SOIC Thermal Resistance, 14L-TSSOP Note 1: The MCP492X family of DACs operate over this extended temperature range, but with reduced performance. Operation in this range must not cause T 150°C. 2004 Microchip Technology Inc. = +2.7V to +5.5V Sym Min Typ Max ...
Page 8
... FIGURE 2-4: Temperature. 0.35 0.3 0.25 0.2 0.15 0.1 0. 4096 85C 25C FIGURE 2-5: Reference. 4096 5.5 . REF = 100 pF - 100 120 Ambient Temperature (ºC) Absolute DNL vs. Ambient Voltage Reference (V) Absolute DNL vs. Voltage 2004 Microchip Technology Inc. ...
Page 9
... Ambient Temperature (ºC) FIGURE 2-7: Absolute INL vs. Ambient Temperature. 3 2.5 2 1 Voltage Reference (V) FIGURE 2-8: Absolute INL vs. V 2004 Microchip Technology Inc. MCP4921/4922 = 0V 2.048V, Gain = REF 4096 0 FIGURE 2- 100 120 FIGURE 2-10: Note: Single device graph (Figure 2-10) for illustration of 64 code effect ...
Page 10
... Ambient FIGURE 2-14: Temperature and Histogram FIGURE 2-15 2.7V Histogram FIGURE 2-16 5.0V). DD 5.5V 5.0V 4.0V 3.0V 2. 100 120 Ambient Temperature (ºC) MCP4922 I vs. Ambient (µA) DD MCP4922 I Histogram DD I (µA) DD MCP4922 I Histogram DD 2004 Microchip Technology Inc. ...
Page 11
... Ambient Temperature and V DD 0.12 0.1 0.08 0.06 0.04 0.02 0 -0.02 -40 - Ambient Temperature (ºC) FIGURE 2-19: Offset Error vs. Ambient Temperature and 2004 Microchip Technology Inc 0V 2.048V, Gain = REF -0.08 5.5V 5.0V -0.1 4.0V -0.12 3.0V 2.7V -0. -0.16 -40 -20 100 120 FIGURE 2-20: ...
Page 12
... Output Shorted to V 3.0V 3.0 2.7V V 2.0 DD 1.0 Output Shorted FIGURE 2-28 100 pF 5.5V 5.0V 4.0V 3.0V 2. 100 120 V Low Limit vs. Ambient OUT . V DD 5.5V 5.0V 4.0V 3.0V 2. 100 120 I High Short vs. OUT . (mA) OUT Gain = 1. OUT OUT 2004 Microchip Technology Inc. ...
Page 13
... OUT V OUT SCK LDAC Time (1 µs/div) FIGURE 2-30: V Fall Time. OUT V OUT SCK LDAC Time (1 µs/div) FIGURE 2-31: V Rise Time 50%. OUT 2004 Microchip Technology Inc. MCP4921/4922 = 0V 2.048V, Gain = REF V OUT LDAC Time (1 µs/div) FIGURE 2-32 OUT SCK LDAC Time (1 µs/div) ...
Page 14
... D = 1696 - 1952 D = 2208 D = 2464 D = 2720 -135 D = 2976 D = 3232 D = 3488 D = 3744 -180 100 1,000 FIGURE 2-37 100 pF 160 D = 416 D = 672 D = 928 D = 1184 D = 1440 D = 1696 D = 1952 D = 2208 D = 2464 D = 2720 D = 2976 D = 3232 D = 3488 D = 3744 1,000 Frequency (kHz) Phase Shift. 2004 Microchip Technology Inc. ...
Page 15
... PIN DESCRIPTIONS The descriptions of the pins are listed in Table 3-1. TABLE 3-1: PIN FUNCTION TABLE MCP4921 MCP4922 Pin No. Pin No — — 6 — — 9 — 10 — 3.1 Positive Power Supply Input ( the positive power supply input. The input power DD supply is relative to AV and can range from 2 ...
Page 16
... LSB, excluding the effects of offset error. REF INL < 0 Actual transfer function Ideal transfer function INL < 0 DAC Output INL Accuracy. Actual transfer function Ideal transfer function Wide code, > 1 LSB Narrow code < 1 LSB DAC Output DNL Accuracy. 2004 Microchip Technology Inc. ...
Page 17
... Shutdown mode can be entered by using either hard- ware or software commands. The hardware pin (SHDN) is only available on the MCP4922. During Shutdown mode, the supply current is isolated from most of the internal circuitry. The serial interface remains active, thus allowing a write command to ), with a typical bring the device out of Shutdown mode ...
Page 18
... CS occurs prior, shifting of data into the input registers will be aborted. W-0 W-x W-x W-x SHDN D11 D10 D9 W-x W-x W Unimplemented bit, read as ‘0’ bit is cleared ’s and DAC ’s outputs register. X W-x D8 bit 8 W-x W-x W bit bit is unknown 2004 Microchip Technology Inc. ...
Page 19
... SCK config bits A/B BUF GA SHDN D11 D10 SDI LDAC V OUT FIGURE 5-1: Write Command. 2004 Microchip Technology Inc data bits MCP4921/4922 (mode 1,1) (mode 0,0) DS21897A-page 19 ...
Page 20
... Particularly harsh environments may require shielding of critical signals. Breadboards and wire-wrapped boards are not recommended if low noise is desired. and 0.1 µF 0.1 µF V REFA OUTA SDI V REFB V OUTB AV SDO SS SCK LDAC Typical Connection 2004 Microchip Technology Inc. ...
Page 21
... V OUT trip EXAMPLE 6-1: Set Point or Threshold Calibration. 2004 Microchip Technology Inc. 6.4.1.1 If the output range is reduced relative to AV reducing V range of 2.7V to REF put step. If the application is calibrating the threshold of a diode, transistor or resistor tied theshold range of 0.8V may be desired to provide 200 µ ...
Page 22
... The MCP492X’s low, ±0.75 (max.) DNL performance is critical to meet calibration accuracy in production CC+ sense trip 0.1 µ CC OUT + CC then creating REF SS Example 6-2 and Example 6-4 V CC+ Comparator V CC Gain select ( Digital value of DAC (0 – 4096 2004 Microchip Technology Inc. ...
Page 23
... REF and the gain will be 0. 2004 Microchip Technology Inc. Example 6-3 illustrates a simple bipolar voltage source configuration. R while R and R 3 offset. Note that R4 can be tied higher offset is desired. Note that a pull- could be used, instead of R REF desired. ...
Page 24
... MCP4921/4922 6.6 Selectable Gain and Offset Bipolar Voltage Output Using A Dual DAC In some applications, precision digital control of the output range is desirable. Example 6-4 illustrates how to use the MCP4922 to achieve this in a bipolar or single-supply application REFA V OUTA MCP492X DAC REFB V OUTB MCP492X DAC SPI™ ...
Page 25
... EXAMPLE 6-5: Simple, Double-Precision DAC. 2004 Microchip Technology Inc. 1. Calculate the resolution needed: 4.1V/1uV = 4.1e06. Since 2 resolution is desired. Since DNL = ±0.75 LSB, this design can be attempted with the MCP492X. 2. Since DAC its output only needs to be “pulled” 1/1000 to meet the 1 µV target. Dividing V ...
Page 26
... Examples 6-2 to 6-6, extends the b output range and power to meet the precise needs of the application. R sense V REF SPI™ EXAMPLE 6-7: and serially configure the REF = V (D/2048). OUT IN V RPM_SET V RPM OUT MCP492X – V – sense Multiplier Mode. 2004 Microchip Technology Inc. ...
Page 27
... Please www.microchip.com for further information on this products capabilities and availability. 2004 Microchip Technology Inc. MCP4921/4922 7.2 Application Notes and Tech Briefs Application notes illustrating the performace and imple- mentation of the MCP492X are planned but currently not released. Please refer to www.microchip.com for ...
Page 28
... Standard marking consists of Microchip part number, year code, week code, traceability code (facility code, mask rev#, and assembly code). For marking beyond this, certain price adders apply. Please check with your Microchip Sales Office. DS21897A-page 28 Example: 4921E 412256 Example: MCP4921 E/P256 0412 Example: MCP4921 E/SN0412 256 2004 Microchip Technology Inc. ...
Page 29
... Package Marking Information (Continued) 14-Lead PDIP (300 mil) (MCP4922) XXXXXXXXXXXXXX XXXXXXXXXXXXXX YYWWNNN 14-Lead SOIC (150 mil) (MCP4922) XXXXXXXXXX XXXXXXXXXX YYWWNNN 14-Lead TSSOP (MCP4922) XXXXXX YYWW NNN 2004 Microchip Technology Inc. MCP4921/4922 Example: MCP4922E/P 0412256 Example: MCP4922E/SL 0412256 Example: 4922E/ST 0412 ...
Page 30
... A2 MILLIMETERS* MIN NOM MAX 8 0.65 BSC - - 1.10 0.75 0.85 0.95 0.00 - 0.15 4.90 BSC 3.00 BSC 3.00 BSC 0.40 0.60 0.80 0.95 REF 0° - 8° 0.08 - 0.23 0.22 - 0.40 5° - 15° 5° - 15° 2004 Microchip Technology Inc. ...
Page 31
... Mold Draft Angle Top Mold Draft Angle Bottom * Controlling Parameter § Significant Characteristic Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010” (0.254mm) per side. JEDEC Equivalent: MS-001 Drawing No. C04-018 2004 Microchip Technology Inc ...
Page 32
... A2 MILLIMETERS MIN NOM MAX 8 1.27 1.35 1.55 1.75 1.32 1.42 1.55 0.10 0.18 0.25 5.79 6.02 6.20 3.71 3.91 3.99 4.80 4.90 5.00 0.25 0.38 0.51 0.48 0.62 0. 0.20 0.23 0.25 0.33 0.42 0. 2004 Microchip Technology Inc. ...
Page 33
... Mold Draft Angle Bottom * Controlling Parameter § Significant Characteristic Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010” (0.254mm) per side. JEDEC Equivalent: MS-001 Drawing No. C04-005 2004 Microchip Technology Inc Units INCHES* ...
Page 34
... A2 MILLIMETERS MIN NOM MAX 14 1.27 1.35 1.55 1.75 1.32 1.42 1.55 0.10 0.18 0.25 5.79 5.99 6.20 3.81 3.90 3.99 8.56 8.69 8.81 0.25 0.38 0.51 0.41 0.84 1. 0.20 0.23 0.25 0.36 0.42 0. 2004 Microchip Technology Inc. ...
Page 35
... Mold Draft Angle Bottom * Controlling Parameter § Significant Characteristic Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .005” (0.127mm) per side. JEDEC Equivalent: MO-153 Drawing No. C04-087 2004 Microchip Technology Inc Units INCHES ...
Page 36
... MCP4921/4922 NOTES: DS21897A-page 36 2004 Microchip Technology Inc. ...
Page 37
... Extended Temperature, 8LD PDIP package. a) MCP4922T-E/SL: Tape and Reel Extended Temperature, 14LD SOIC package. b) MCP4922T-E/ST: Tape and Reel Extended Temperature, 14LD TSSOP package. c) MCP4922-E/P: Extended Temperature, 14LD PDIP package. d) MCP4922-E/SL: Extended Temperature, 14LD SOIC package. e) MCP4922-E/ST: Extended Temperature, 14LD TSSOP package. DS21897A-page 37 ...
Page 38
... MCP4921/4922 NOTES: DS21897A-page 38 2004 Microchip Technology Inc. ...
Page 39
... PICLAB, PICtail, PowerCal, PowerInfo, PowerMate, PowerTool, rfLAB, rfPICDEM, Select Mode, Smart Serial, SmartTel and Total Endurance are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. ...
Page 40
... Via Quasimodo, 12 20025 Legnano (MI) Milan, Italy Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands Waegenburghtplein 4 NL-5152 JR, Drunen, Netherlands Tel: 31-416-690399 Fax: 31-416-690340 United Kingdom 505 Eskdale Road Winnersh Triangle Wokingham Berkshire, England RG41 5TU Tel: 44-118-921-5869 Fax: 44-118-921-5820 05/28/04 2004 Microchip Technology Inc. ...