MAX5544CSA+ Maxim Integrated Products, MAX5544CSA+ Datasheet - Page 8

• Manufacturer Part Number: MAX5544CSA+
• Description: IC DAC 14BIT 5V SERIAL 8-SOIC
• Manufacturer: Maxim Integrated Products

Specifications of MAX5544CSA+

• Settling Time: 1µs
• Number Of Bits: 14
• Data Interface: Serial
• Number Of Converters: 1
• Voltage Supply Source: Single Supply
• Power Dissipation (max): 1.5mW
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
8 _____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 1999 Maxim Integrated Products
Figure 3. Typical Operating Circuit
Low-Cost, +5V, Serial-Input,
Voltage-Output, 14-Bit DAC
The external buffer amplifier’s gain-bandwidth product
is important because it increases the settling time by
adding another time constant to the output response.
The effective time constant of two cascaded systems,
each with a single time-constant response, is approxi-
mately the root square sum of the two time constants.
The DAC output’s time constant is 1µs / 10.4 = 96ns,
ignoring the effect of additional capacitance. If the time
constant of an external amplifier with 1MHz bandwidth
is 1 / 2π (1MHz) = 159ns, then the effective time con-
stant of the combined system is:
This suggests that the settling time to within 1/2LSB of
the final output voltage, including the external buffer
amplifier, will be approximately 10.4
The digital interface for the 14-bit DAC is based on a 3-
wire standard that is SPI/QSPI/MICROWIRE compati-
ble. The three digital inputs (CS, DIN, and SCLK) load
the digital input data serially into the DAC.
All of the digital inputs include Schmitt-trigger buffers to
accept slow-transition interfaces. This means that opto-
couplers can interface directly to the MAX5544 without
additional external logic. The digital inputs are TTL/
CMOS-logic compatible.
Figure 3 shows the MAX5544 configured for unipolar
operation with an external op amp. The op amp is set for
unity gain, and Table 1 shows the codes for this circuit.
Digital Inputs and Interface Logic




MC68XXXX
( )
96ns
2
PCS0
MOSI
SCLK
+
(
159ns
Unipolar Configuration
)
2




CS
DIN
SCLK
=
186ns
•
186ns = 1.93µs.
Printed USA
0.1µF
DGND
+5V
V
DD
MAX5544
+2.5V
REF
0.1µF
10µF
AGND
For optimum system performance, use PC boards with
separate analog and digital ground planes. Wire-wrap
boards are not recommended. Connect the two ground
planes together at the low-impedance power-supply
source. Connect DGND and AGND together at the IC.
The best ground connection can be achieved by con-
necting the DAC’s DGND and AGND pins together and
connecting that point to the system analog ground
plane. If the DAC’s DGND is connected to the system
digital ground, digital noise may get through to the
DAC’s analog portion.
Bypass V
between V
close to the device. Ferrite beads can also be used to
further isolate the analog and digital power supplies.
TRANSISTOR COUNT: 2209
SUBSTRATE CONNECTED TO DGND
Table 1. Unipolar Code Table
DAC LATCH CONTENTS
1111 1111 1111 11(00)
1000 0000 0000 00(00)
0000 0000 0000 01(00)
0000 0000 0000 00(00)
MSB
is a registered trademark of Maxim Integrated Products.
DD
DD
with a 0.1µF ceramic capacitor connected
and AGND. Mount it with short leads
OUT
LSB
Power-Supply Bypassing and
MAX495
V
V
V
0V
EXTERNAL OP AMP
REF
REF
REF
ANALOG OUTPUT, V
Chip Information
Ground Management
•
•
•
(8192 / 16,384) = 1/ 2 V
(16,383 / 16,384)
(1 / 16,834)
UNIPOLAR
OUT
OUT
REF