AD9760ARU Analog Devices Inc, AD9760ARU Datasheet - Page 14

• Manufacturer Part Number: AD9760ARU
• Description: IC DAC 10BIT 125MSPS 28-TSSOP
• Manufacturer: Analog Devices Inc
• Series: TxDAC®r

Specifications of AD9760ARU

• Settling Time: 35ns
• Rohs Status: RoHS non-compliant
• Number Of Bits: 10
• Number Of Converters: 1
• Voltage Supply Source: Analog and Digital
• Power Dissipation (max): 175mW
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 28-TSSOP
• Number Of Channels: 1
• Resolution: 10b
• Interface Type: Parallel
• Single Supply Voltage (typ): 5V
• Dual Supply Voltage (typ): Not RequiredV
• Power Supply Requirement: Analog and Digital
• Output Type: Current
• Single Supply Voltage (min): 2.7V
• Single Supply Voltage (max): 5.5V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 28
• For Use With: AD9760-EBZ - BOARD EVAL FOR AD9760
• Data Interface: -
• Lead Free Status / RoHS Status: Not Compliant

AD9760
The enhancement in distortion performance becomes more
significant as the frequency content of the reconstructed wave-
form increases. This is due to the first order cancellation of
various dynamic common-mode distortion mechanisms, digi-
tal feedthrough and noise.
Performing a differential-to-single-ended conversion via a
transformer also provides the ability to deliver twice the re-
constructed signal power to the load (i.e., assuming no source
termination). Since the output currents of I
complementary, they become additive when processed differ-
entially. A properly selected transformer will allow the AD9760
to provide the required power and voltage levels to different
loads. Refer to Applying the AD9760 section for examples of
various output configurations.
The output impedance of I
equivalent parallel combination of the PMOS switches associ-
ated with the current sources and is typically 100 kΩ in parallel
with 5 pF. It is also slightly dependent on the output voltage
(i.e., V
As a result, maintaining I
via an I-V op amp configuration will result in the optimum dc
linearity. Note the INL/DNL specifications for the AD9760 are
measured with I
op amp.
I
pliance range that must be adhered to in order to achieve opti-
mum performance. The negative output compliance range of
–1.0 V is set by the breakdown limits of the CMOS process.
Operation beyond this maximum limit may result in a break-
down of the output stage and affect the reliability of the AD9760.
The positive output compliance range is slightly dependent on
the full-scale output current, I
its nominal 1.25 V for an I
I
single-ended or differential output is achieved when the maximum
full-scale signal at I
plications requiring the AD9760’s output (i.e., V
V
accordingly. Operation beyond this compliance range will ad-
versely affect the AD9760’s linearity performance and subse-
quently degrade its distortion performance.
DIGITAL INPUTS
The AD9760’s digital input consists of 10 data input pins and a
clock input pin. The 10-bit parallel data inputs follow standard
positive binary coding where DB9 is the most significant bit
(MSB) and DB0 is the least significant bit (LSB). I
duces a full-scale output current when all data bits are at
Logic 1. I
scale current split between the two outputs as a function of the
input code.
The digital interface is implemented using an edge-triggered
master slave latch. The DAC output is updated following the
rising edge of the clock as shown in Figure 1 and is designed to
support a clock rate as high as 125 MSPS. The clock can be
operated at any duty cycle that meets the specified latch pulse-
width. The setup and hold times can also be varied within the
OUTA
OUTFS
OUTB
and I
) to extend its output compliance range should size R
OUTA
= 2 mA. The optimum distortion performance for a
OUTB
OUTB
and V
produces a complementary output with the full-
OUTA
also have a negative and positive voltage com-
OUTB
OUTA
maintained at a virtual ground via an
) due to the nature of a PMOS device.
and I
OUTA
OUTA
OUTFS
OUTB
OUTFS
and/or I
and I
= 20 mA to 1.00 V for an
does not exceed 0.5 V. Ap-
. It degrades slightly from
OUTB
OUTB
is determined by the
OUTA
at a virtual ground
and I
OUTA
OUTA
OUTB
and/or
pro-
are
LOAD
–14–
clock cycle as long as the specified minimum times are met
although the location of these transition edges may affect digital
feedthrough and distortion performance. Best performance is
typically achieved when the input data transitions on the falling edge
of a 50% duty cycle clock.
The digital inputs are CMOS compatible with logic thresholds,
V
(DVDD) or
The internal digital circuitry of the AD9760 is capable of oper-
ating over a digital supply range of 2.7 V to 5.5 V. As a result,
the digital inputs can also accommodate TTL levels when
DVDD is set to accommodate the maximum high level voltage
V
compatibility with most TTL logic families. Figure 46 shows the
equivalent digital input circuit for the data and clock inputs.
The sleep mode input is similar with the exception that it con-
tains an active pull-down circuit, ensuring that the AD9760
remains enabled if this input is left disconnected.
Since the AD9760 is capable of being updated up to 125 MSPS,
the quality of the clock and data input signals are important in
achieving the optimum performance. The drivers of the digital
data interface circuitry should be specified to meet the mini-
mum setup and hold times of the AD9760 as well as its required
min/max input logic level thresholds. Typically, the selection of
the slowest logic family that satisfies the above conditions will
result in the lowest data feedthrough and noise.
Digital signal paths should be kept short and run lengths
matched to avoid propagation delay mismatch. The insertion of
a low value resistor network (i.e., 20 Ω to 100 Ω) between the
AD9760 digital inputs and driver outputs may be helpful in
reducing any overshooting and ringing at the digital inputs that
contribute to data feedthrough. For longer run lengths and high
data update rates, strip line techniques with proper termination
resistors should be considered to maintain “clean” digital in-
puts. Also, operating the AD9760 with reduced logic swings and
a corresponding digital supply (DVDD) will also reduce data
feedthrough.
The external clock driver circuitry should provide the AD9760
with a low jitter clock input meeting the min/max logic levels
while providing fast edges. Fast clock edges will help minimize
any jitter that will manifest itself as phase noise on a recon-
structed waveform. Thus, the clock input should be driven by
the fastest logic family suitable for the application.
THRESHOLD
OH(MAX)
. A DVDD of 3 V to 3.3 V will typically ensure proper
set to approximately half the digital positive supply
Figure 46. Equivalent Digital Input
V
DIGITAL
THRESHOLD
INPUT
= DVDD/2 (± 20%)
DVDD
REV. B