AD5648ARUZ-2 Analog Devices Inc, AD5648ARUZ-2 Datasheet - Page 20

• Manufacturer Part Number: AD5648ARUZ-2
• Description: IC DAC 14BIT OCT 5V REF 16-TSSOP
• Manufacturer: Analog Devices Inc

Specifications of AD5648ARUZ-2

• Data Interface: DSP, MICROWIRE™, QSPI™, Serial, SPI™
• Settling Time: 6µs
• Number Of Bits: 14
• Number Of Converters: 8
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 105°C
• Mounting Type: Surface Mount
• Package / Case: 16-TSSOP
• Resolution (bits): 14bit
• Sampling Rate: 95kSPS
• Input Channel Type: Serial
• Supply Voltage Range - Analogue: 2.7V To 3.6V, 4.5V To 5.5V
• Supply Current: 2mA
• Digital Ic Case: RoHS Compliant
• Number Of Channels: 8
• Resolution: 14b
• Conversion Rate: 95KSPS
• Interface Type: SER 3W SPI QSPI UW
• Single Supply Voltage (typ): 3.3/5V
• Dual Supply Voltage (typ): Not RequiredV
• Architecture: Resistor-String
• Power Supply Requirement: Single
• Output Type: Voltage
• Integral Nonlinearity Error: ±8+/- LSB
• Single Supply Voltage (min): 2.7V
• Single Supply Voltage (max): 5.5V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temp Range: -40C to 105C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 16
• Package Type: TSSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Power Dissipation (max): -
• Lead Free Status / Rohs Status: Compliant

AD5628/AD5648/AD5668
THEORY OF OPERATION
D/A SECTION
The AD5628/AD5648/AD5668 DACs are fabricated on a
CMOS process. The architecture consists of a string of DACs
followed by an output buffer amplifier. Each part includes an
internal 1.25 V/2.5 V, 5 ppm/°C reference with an internal gain
of 2. Figure 54 shows a block diagram of the DAC architecture.
Because the input coding to the DAC is straight binary, the ideal
output voltage when using an external reference is given by
The ideal output voltage when using the internal reference is
given by
where:
D = decimal equivalent of the binary code that is loaded to the
DAC register.
N = the DAC resolution.
RESISTOR STRING
The resistor string section is shown in Figure 55. It is simply a
string of resistors, each of value R. The code loaded into the
DAC register determines at which node on the string the
voltage is tapped off to be fed into the output amplifier. The
voltage is tapped off by closing one of the switches connecting
the string to the amplifier. Because it is a string of resistors, it is
guaranteed monotonic.
0 to 4095 for AD5628 (12 bits).
0 to 16,383 for AD5648 (14 bits).
0 to 65,535 for AD5668 (16 bits).
V
V
OUT
OUT
REGISTER
=
=
DAC
V
2
×
REFIN
V
REFOUT
⎛ ×
Figure 54. DAC Architecture
⎜
⎝
V
REFIN
2
D
N
⎛ ×
⎜
⎝
⎞
⎟
⎠
RESISTOR
2
D
STRING
N
V
DD
⎞
⎟
⎠
GND
REF
AMPLIFIER
(GAIN = ×2)
OUTPUT
V
OUT
Rev. E | Page 20 of 28
INTERNAL REFERENCE
The AD5628/AD5648/AD5668 have an on-chip reference with
an internal gain of 2. The AD5628/AD5648/AD5668-1 have a
1.25 V, 5 ppm/°C reference, giving a full-scale output of 2.5 V;
the AD5628/AD5648/AD5668-2, -3 have a 2.5 V, 5 ppm/°C
reference, giving a full-scale output of 5 V. The on-board
reference is off at power-up, allowing the use of an external
reference. The internal reference is enabled via a write to the
control register (see Table 7).
The internal reference associated with each part is available at
the V
used to drive external loads. When using the internal reference,
it is recommended that a 100 nF capacitor be placed between
the reference output and GND for reference stability.
Individual channel power-down is not supported while using
the internal reference.
REFOUT
pin. A buffer is required if the reference output is
R
R
R
R
R
Figure 55. Resistor String
TO OUTPUT
AMPLIFIER