LXMG1626-12-45 MICROSEMI, LXMG1626-12-45 Datasheet - Page 2

• Manufacturer Part Number: LXMG1626-12-45
• Manufacturer: MICROSEMI

Specifications of LXMG1626-12-45

• Operating Temperature Classification: Commercial
• Pin Count: 12
• Lead Free Status / Rohs Status: Compliant

Copyright © 2007
Rev.1.1, 2007-08-24
This module has been designed to operate over a wide range of input and output conditions. However, best efficiency and performance
will be obtained if the module is operated under the condition listed in the ‘R.C.’ column. Min. and Max. columns indicate values beyond
which the inverter, although operational, will not function optimally.
Unless otherwise specified, the following specifications apply over the recommended operating condition and ambient temperature of
0°C to 60°C except where otherwise noted.
Input Signal Voltage (V
Input Power ......................................................................................................................................................................... 8W
Output Voltage, no load ............................................................................................................ Internally Limited to 1500V
Output Current (per lamp) ...........................................................................................................6.6mA
Output Power ..................................................................................................................................................................... 6W
Input Signal Voltage ( SLEEP Input) ..................................................................................................................-0.3V to 13.2V
Input Signal Voltage (BRITE) ...............................................................................................................................-0.3V to 5.5V
Ambient Operating Temperature, zero airflow.....................................................................................................-30°C to 80°C
Operating Relative Humidity, non-condensing ................................................................................................................
Storage Temperature Range...............................................................................................................................-40°C to 85°C
²At input voltages below 12V the inverter may not be able to output the full 6mA
¹ Based on single lamp voltage measurement, use of lamps outside of this range may result is false triggering of the fault detection circuitry.
Output Power
Linear BRITE Control Input Voltage Range
Lamp Operating Voltage
Lamp Current (Full Brightness, per Lamp)
Operating Ambient Temperature Range
Input Supply Voltage Range (Fully Regulated Lamp
Current)
Input Supply Voltage Range (Functional)
OUTPUT PIN CHARACTERISTICS
Full Bright Lamp Current (two lamps)
Full Bright Lamp Current (two lamps)
Output Current Lamp to Lamp
Deviation
Min. Average Lamp Current
Lamp Start Voltage
Operating Frequency
Burst Frequency
FAULT Output Voltage High
FAULT Output Voltage Low
TM
Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of specified
terminal.
Parameter
Parameter
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: [phone]
IN
) ......................................................................................................................................-0.3V to 15V
R E C O M M E N D E D O P E R A T I N G C O N D I T I O N S ( R . C . )
E L E C T R I C A L C H A R A C T E R I S T I C S
Symbol
FAULT
FAULT
A B S O L U T E M A X I M U M R A T I N G S
I
I
I
f
LL%DEV
I
L(MAX)
L(MAX)
BURST
L(MIN)
V
f
LS
O
VH
VL
Analog Mixed Signal Group
V
I
V
I
V
I
V
I
V
V
Output Burst Frequency
FAULT = -10uA
FAULT = 10uA
SET
SET
SET
SET
BRT_ADJ
BRT_ADJ
BRT_ADJ
BRT_ADJ
IN
BRT_ADJ
> 10.8V
= Ground
= Open
= Open
= Ground; I
®
Microsemi
Symbol
V
> 2.0V,
> 2.0V,
> 2.0V,
= 0V,
= 2.0V,
I
V
O(LAMP)
PanelMatch™ StayLit™
BRT_ADJ
V
P
LAMP
T
IN
O
A
SLEEP
OUT
Test Conditions
SLEEP
SLEEP
SLEEP
SLEEP
RMS
= I
12V Dual 6W CCFL Programmable Inverter Module
per lamp in all configurations.
MAX
> 2.0V, V
Recommended Operating Conditions
> 2.0V, V
> 2.0V, V
> 2.0V, V
> 2.0V, V
* SQRT of % duty cycle
Min
10.8
10.2
385
5.0
-30
0
IN
P
IN
IN
IN
= 12V
IN
= 12V
= 12V
= 12V
= 12V
RODUCTION
R.C.
435
4.5
12
12
D
ATASHEET
1250
Min
55.2
215
11
LXMG1626-12-45
9
3
LXMG1626-12-45
Max
13.2
13.6
485
RMS
5.5
2.0
6.0
80
1400
Typ
57.6
225
(Internally Limited)
1.6
3.5
0.3
10
12
5
Max
235
0.8
11
13
60
mA
Units
V
RMS
°C
W
V
V
RMS
≤
90%
¹
RMS
Units
mA
mA
mA
²
V
kHz
Hz
%
RMS
V
V
Page 2
RMS
RMS
RMS