BTS441TSNK Infineon Technologies, BTS441TSNK Datasheet
BTS441TSNK
Specifications of BTS441TSNK
Related parts for BTS441TSNK
BTS441TSNK Summary of contents
Page 1
... N channel vertical power FET with charge pump, ground referenced CMOS compatible input, monolithically integrated in Smart SIPMOS Š technology. • Providing embedded protective functions. • μC compatible power switch for 5V and applications • All types of resistive, inductive and capacitve loads • Most suitable for loads with high inrush currents lamps • ...
Page 2
Data sheet PROFET 2 BTS441T Rev. 1.11, 2008-12-09 ...
Page 3
... setup without the DUT connected to the generator per ISO 7637-1 and DIN 40839 Load dump the maximum inductive switch off energy AS 5) Device on 50mm*50mm*1.5mm epoxy PCB FR4 with 6cm connection. PCB is vertical without blown air. Data sheet = ...
Page 4
... Electrical Characteristics Parameter and Conditions at T =-40...+150° unless otherwise specified j bb Load Switching Capabilities and Characteristics On-state resistance (V bb (pin3) to OUT (pin5) ≥ see diagram page 9 Nominal load current (pin ‘ISO 10483-1, 6.7: V =0.5V Output current while GND disconnected or (pin 5) ...
Page 5
... (see timing diagrams, page 10 Thermal shutdown time 11)12) (see timing diagram on page 10) Output clamp (inductive load switch off OUT = ON(CL Thermal overload trip temperature Thermal hysteresis Reverse battery (pin Reverse battery voltage drop ( - Integrated protection functions are designed to prevent IC destruction under fault conditions described in the 10 data sheet. Fault conditions are considered as " ...
Page 6
Parameter and Conditions at T =-40...+150° unless otherwise specified j bb Input 14) Input resistance Input turn-on threshold voltage Input turn-off threshold voltage Input threshold hysteresis Off state input current (pin 2) On state input current ...
Page 7
Terms Input circuit (ESD protection) The use of ESD zener diodes as voltage clamp at DC conditions is not recommended. Inductive and overvoltage output clamp V clamped typ. ON Data sheet Overvolt. and reverse batt. protection V ...
Page 8
... For inductive load currents up to the limits defined (max. ratings and diagram on page 8) each switch is protected against loss Consider at your PCB layout that in the case of Vbb dis- connection with energized inductive load all the load current flows through the GND connection ...
Page 9
Typ. on-state resistance high L R [mΩ] ON Typ. standby current , I RII M = 9...34 V, IN1,2 = low bb I ...
Page 10
... Timing diagrams Figure 1a: V turn on: bb proper turn on under all conditions Figure 2a: Switching a resistive load, turn-on/off time and slew rate definition: on Data sheet Figure 2b: Switching a lamp, Figure 3a: Short circuit shut down by overtemperature, reset by cooling Heating up may require several milliseconds, depending on external conditions ...
Page 11
Package Outlines 0...0.3 0...0. Typical All metal surfaces tin plated, except area of cut. figure 5: PG-TO220-5-11 Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government ...
Page 12
C 0...0.15 1) Typical Metal surface min 7.25 12.3 All metal surfaces tin plated, except area of cut. Figure 6: PG-TO220-5-12 Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly products ...
Page 13
Typical Metal surface min 7.25 6.9 All metal surfaces tin plated, except area of cut. Figure 7: PG-TO263-5-2 Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally ...
Page 14
Revision History Revision Date Changes 1.11 2008-12-09 RoHS-compliant PG-TO220 and PG-TO263 packages version of the BTS441T All pages: Infineon logo updated Page 1: Added “AEC qualified” and “RoHS” logo, added “Green Product (RoHS compliant)” and “AEC qualified” statement to feature ...
Page 15
... Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life ...