EPM7512AEQC208-7 Altera, EPM7512AEQC208-7 Datasheet - Page 25

• Manufacturer Part Number: EPM7512AEQC208-7
• Description: IC MAX 7000 CPLD 512 208-PQFP
• Manufacturer: Altera
• Series: MAX® 7000Ar

Specifications of EPM7512AEQC208-7

• Programmable Type: In System Programmable
• Delay Time Tpd(1) Max: 7.5ns
• Voltage Supply - Internal: 3 V ~ 3.6 V
• Number Of Logic Elements/blocks: 32
• Number Of Macrocells: 512
• Number Of Gates: 10000
• Number Of I /o: 176
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 208-MQFP, 208-PQFP
• Voltage: 3.3V
• Memory Type: EEPROM
• Number Of Logic Elements/cells: 32
• Family Name: MAX 7000A
• # Macrocells: 512
• Number Of Usable Gates: 10000
• Frequency (max): 166.67MHz
• Propagation Delay Time: 7.5ns
• Number Of Logic Blocks/elements: 32
• # I/os (max): 176
• Operating Supply Voltage (typ): 3.3V
• In System Programmable: Yes
• Operating Supply Voltage (min): 3V
• Operating Supply Voltage (max): 3.6V
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 208
• Package Type: PQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Features: -
• Lead Free Status / Rohs Status: Not Compliant
• Other names: 544-2359

MAX 7000A Programmable Logic Device Data Sheet
Open-Drain Output Option
MAX 7000A devices provide an optional open-drain (equivalent to
open-collector) output for each I/O pin. This open-drain output enables
the device to provide system-level control signals (e.g., interrupt and
write enable signals) that can be asserted by any of several devices. This
output can also provide an additional wired-OR plane.
Open-drain output pins on MAX 7000A devices (with a pull-up resistor to
the 5.0-V supply) can drive 5.0-V CMOS input pins that require a high
V
. When the open-drain pin is active, it will drive low. When the pin is
IH
inactive, the resistor will pull up the trace to 5.0 V to meet CMOS V
OH
requirements. The open-drain pin will only drive low or tri-state; it will
never drive high. The rise time is dependent on the value of the pull-up
resistor and load impedance. The I
current specification should be
OL
considered when selecting a pull-up resistor.
Programmable Ground Pins
Each unused I/O pin on MAX 7000A devices may be used as an
additional ground pin. In EPM7128A and EPM7256A devices, utilizing
unused I/O pins as additional ground pins requires using the associated
macrocell. In MAX 7000AE devices, this programmable ground feature
does not require the use of the associated macrocell; therefore, the buried
macrocell is still available for user logic.
Slew-Rate Control
The output buffer for each MAX 7000A I/O pin has an adjustable output
slew rate that can be configured for low-noise or high-speed performance.
A faster slew rate provides high-speed transitions for high-performance
systems. However, these fast transitions may introduce noise transients
into the system. A slow slew rate reduces system noise, but adds a
nominal delay of 4 to 5 ns. When the configuration cell is turned off, the
slew rate is set for low-noise performance. Each I/O pin has an individual
EEPROM bit that controls the slew rate, allowing designers to specify the
slew rate on a pin-by-pin basis. The slew rate control affects both the rising
and falling edges of the output signal.
Altera Corporation
25