EPM7256SRC208-15 Altera, EPM7256SRC208-15 Datasheet - Page 21

• Manufacturer Part Number: EPM7256SRC208-15
• Description: IC MAX 7000 CPLD 256 208-RQFP
• Manufacturer: Altera
• Series: MAX® 7000r

Specifications of EPM7256SRC208-15

• Programmable Type: In System Programmable
• Delay Time Tpd(1) Max: 15.0ns
• Voltage Supply - Internal: 4.75 V ~ 5.25 V
• Number Of Logic Elements/blocks: 16
• Number Of Macrocells: 256
• Number Of Gates: 5000
• Number Of I /o: 164
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 208-RQFP
• Voltage: 5V
• Memory Type: EEPROM
• Number Of Logic Elements/cells: 16
• Family Name: MAX 7000S
• # Macrocells: 256
• Number Of Usable Gates: 5000
• Frequency (max): 100MHz
• Propagation Delay Time: 15ns
• Number Of Logic Blocks/elements: 16
• # I/os (max): 164
• Operating Supply Voltage (typ): 5V
• In System Programmable: Yes
• Operating Supply Voltage (min): 4.75V
• Operating Supply Voltage (max): 5.25V
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 208
• Package Type: RQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Features: -
• Lead Free Status / Rohs Status: Not Compliant
• Other names: 544-2068; EPM7256SRC208-15

Programming with
External Hardware
Altera Corporation
f
f
By using an external 5.0-V pull-up resistor, output pins on MAX
7000S devices can be set to meet 5.0-V CMOS input voltages. When
V
pull-up transistor, allowing the external pull-up resistor to pull the
output high enough to meet 5.0-V CMOS input voltages. When
V
because the pull-up transistor will already turn off when the pin
exceeds approximately 3.8 V, allowing the external pull-up resistor to
pull the output high enough to meet 5.0-V CMOS input voltages.
Slew-Rate Control
The output buffer for each MAX 7000E and MAX 7000S I/O pin has
an adjustable output slew rate that can be configured for low-noise
or high-speed performance. A faster slew rate provides high-speed
transitions for high-performance systems. However, these fast
transitions may introduce noise transients into the system. A slow
slew rate reduces system noise, but adds a nominal delay of 4 to 5 ns.
In MAX 7000E devices, when the Turbo Bit is turned off, the slew
rate is set for low noise performance. For MAX 7000S devices, each
I/O pin has an individual EEPROM bit that controls the slew rate,
allowing designers to specify the slew rate on a pin-by-pin basis.
MAX 7000 devices can be programmed on Windows-based PCs with
the Altera Logic Programmer card, the Master Programming Unit
(MPU), and the appropriate device adapter. The MPU performs a
continuity check to ensure adequate electrical contact between the
adapter and the device.
For more information, see the
Sheet.
The Altera development system can use text- or waveform-format
test vectors created with the Text Editor or Waveform Editor to test
the programmed device. For added design verification, designers
can perform functional testing to compare the functional behavior of
a MAX 7000 device with the results of simulation. Moreover, Data
I/O, BP Microsystems, and other programming hardware
manufacturers also provide programming support for Altera
devices.
For more information, see the
CCIO
CCIO
is 3.3 V, setting the open drain option will turn off the output
is 5.0 V, setting the output drain option is not necessary
MAX 7000 Programmable Logic Device Family Data Sheet
Altera Programming Hardware Data
Programming Hardware
Manufacturers.
21