DLP-245PB-G DLP Design Inc, DLP-245PB-G Datasheet - Page 13

• Manufacturer Part Number: DLP-245PB-G
• Description: MODULE USB-MCU FT245RL W/16F877A
• Manufacturer: DLP Design Inc

Specifications of DLP-245PB-G

• Module/board Type: Development Board
• Interface Type: USB
• Data Bus Width: 8 bit
• Operating Supply Voltage: 5 V
• Product: Interface Modules
• For Use With/related Products: USB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 813-1004

V2.3
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
GROUND
SWVCC
and Q1 MOSFET power switch. R5 and C3 control the power-up rate to help limit inrush current.
GROUND
No connect
EXTVCC
PORTVCC if the module is to be powered by the USB port (typical configuration).
PORTVCC
USB port (typical configuration). 500mA is the maximum current available to the DLP-245PB-G
and target electronics if the USB device is configured for high power.
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
B5
B4
B0
C0
C1
C2
C3
C4
C5
C6
C7
GROUND
(I/O) Port Pin B5 connected to the 16F877A microcontroller.
(I/O) Port Pin B4 connected to the 16F877A microcontroller.
(I/O) Port Pin B0 connected to the 16F877A microcontroller.
(I/O) Port Pin C0 connected to the 16F877A microcontroller.
(I/O) Port Pin C1 connected to the 16F877A microcontroller.
(I/O) Port Pin C2 connected to the 16F877A microcontroller.
(I/O) Port Pin C3 connected to the 16F877A microcontroller.
(I/O) Port Pin C4 connected to the 16F877A microcontroller.
(I/O) Port Pin C5 connected to the 16F877A microcontroller.
(I/O) Port Pin C6 connected to the 16F877A microcontroller.
(I/O) Port Pin C7 connected to the 16F877A microcontroller.
(I/O) Line 7 of the data bus between the 16F877A and the FT245RL USB-FIFO.
(I/O) Line 6 of the data bus between the 16F877A and the FT245RL USB-FIFO.
(I/O) Line 5 of the data bus between the 16F877A and the FT245RL USB-FIFO.
(I/O) Line 4 of the data bus between the 16F877A and the FT245RL USB-FIFO.
(I/O) Line 3 of the data bus between the 16F877A and the FT245RL USB-FIFO.
(I/O) Line 2 of the data bus between the 16F877A and the FT245RL USB-FIFO.
(I/O) Line 1 of the data bus between the 16F877A and the FT245RL USB-FIFO.
(I/O) Line 0 of the data bus between the 16F877A and the FT245RL USB-FIFO.
(Out) Power from EXTVCC (Pin 19) controlled via Pin 10 (POWERN#) of the FT245RL
(In) Use for applying main power (4.4 to 5.25 volts) to the module. Connect to
(Out) Power from USB port. Connect to EXTVCC if module is to be powered by the
Page 13 of
15
February 2007