AD9834CRUZ Analog Devices Inc, AD9834CRUZ Datasheet - Page 28

• Manufacturer Part Number: AD9834CRUZ
• Description: IC DDS 10BIT 75MHZ LP 20-TSSOP
• Manufacturer: Analog Devices Inc

Specifications of AD9834CRUZ

• Design Resources: Amplitude Control Circuit for AD9834 Waveform Generator (CN0156)
• Resolution (bits): 10 b
• Master Fclk: 75MHz
• Tuning Word Width (bits): 28 b
• Voltage - Supply: 2.3 V ~ 5.5 V
• Operating Temperature: -40°C ~ 105°C
• Mounting Type: Surface Mount
• Package / Case: 20-TSSOP
• Synthesizer Type: Frequency
• Frequency: 75MHz
• Supply Voltage Range: 2.3V To 5.5V
• Supply Current: 17mA
• Operating Temperature Range: -40°C To +105°C
• Digital Ic Case Style: TSSOP
• No. Of Pins: 20
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-AD9834EBZ - BOARD EVAL FOR AD9834
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

AD9834
AD9834 TO 80C51/80L51 INTERFACE
Figure 37 shows the serial interface between the AD9834 and
the 80C51/80L51 microcontroller. The microcontroller is
operated in Mode 0 so that TXD of the 80C51/80L51 drives SCLK
of the AD9834, and RXD drives the serial data line (SDATA). The
FSYNC signal is derived from a bit programmable pin on the port
(P3.3 is shown in the diagram). When data is to be transmitted to
the AD9834, P3.3 is taken low. The 80C51/80L51 transmits data
in 8-bit bytes, thus only eight falling SCLK edges occur in each
cycle. To load the remaining eight bits to the AD9834, P3.3 is
held low after the first eight bits have been transmitted, and a
second write operation is initiated to transmit the second byte of
data. P3.3 is taken high following the completion of the second
write operation. SCLK should idle high between the two write
operations. The 80C51/80L51 outputs the serial data in an LSB-
first format. The AD9834 accepts the MSB first (the four MSBs
being the control information, the next four bits being the
address, and the eight LSBs containing the data when writing
to a destination register). Therefore, the transmit routine of the
80C51/80L51 must take this into account and rearrange the bits
so that the MSB is output first.
1
ADDITIONAL PINS OMITTED FOR CLARITY.
80C51/80L51
Figure 37. 80C51/80L51 to AD9834 Interface
RXD
P3.3
TXD
1
FSYNC
SDATA
SCLK
AD9834
1
Rev. C | Page 28 of 36
AD9834 TO DSP56002 INTERFACE
Figure 38 shows the interface between the AD9834 and the
DSP56002. The DSP56002 is configured for normal mode
asynchronous operation with a gated internal clock (SYN = 0,
GCK = 1, SCKD = 1). The frame sync pin is generated internally
(SC2 = 1), the transfers are 16 bits wide (WL1 = 1, WL0 = 0), and
the frame sync signal frames the 16 bits (FSL = 0). The frame sync
signal is available on Pin SC2, but needs to be inverted before
being applied to the AD9834. The interface to the DSP56000/
DSP56001 is similar to that of the DSP56002.
1
ADDITIONAL PINS OMITTED FOR CLARITY.
DSP56002
Figure 38. DSP56002 to AD9834 Interface
SCK
STD
SC2
1
FSYNC
SDATA
SCLK
AD9834
1