D-Z73 SMC Corporation, D-Z73 Datasheet - Page 88

• Manufacturer Part Number: D-Z73
• Description: Autosswitch, Reed, VAC/VDC, 2 Wire, LED, 0.5M
• Manufacturer: SMC Corporation

Specifications of D-Z73

• Technology: Reed

How to Mount and Move the Auto Switch
<Applicable auto switch>
Solid state switch······D-P5DWL
1. Mount the mounting bracket onto the mounting nut by tightening bracket
2. Insert the mounting bracket assembly (bracket + nut) into the mounting
3. Push the auto switch mounting screw lightly into the auto switch through
4. After reconfirming the detecting position, tighten the mounting screw to
Auto Switch Mounting Bracket Part No.
(Including bracket, screw)
Mounting Bracket
Switch mounting bracket fixing screw
Hexagon socket head cap bolt
M3 x 0.5 x 14
fixing screw lightly through the mounting hole on the top of bracket.
groove and set it at the auto switch mounting position.
the mounting hole to secure.
secure the mounting bracket and the auto switch. (Tightening torque
should be 0.5 to 0.7 N·m.)
Cylinder series
CDQ2
MK, MK2
Switch
mounting nut
l
Spring washer
Switch
mounting
bracket
Technical Data 2:
How to Mount and Move the Auto Switch
BQP1-050
40
Rail Mounting Style
BQP1-050
Applicable bore size (mm)
50
BQP1-050
Switch mounting screw
Round head Phillips screw
with spring washer
M3 x 0.5 x 16
63
Magnetic field
resistant
auto switch
BQP1-050
80
—
l
BQP1-050
100
—
1. Insert the hexagon socket head cap screw (M2.5 x 0.45 x 8
2. Install a spring washer in the hexagon socket head cap bolt (M3 x 0.5 x
3. As for switch mounting bracket, slightly thread the hexagon socket head
4. Fit the switch mounting bracket into the switch mounting groove on the
5. After reconfirming the detecting position, tighten the mounting screw to
How to Mount and Move the Auto Switch
Auto Switch Mounting Bracket Part No.
(Including bracket, screw)
• When tightening hexagon socket head cap screw of an auto switch, use a
Tightening Torque
• As a guide, set approximately 0.3 to 0.5 N·m for M2.5, 0.5 to 0.7 N·m for
Auto Switch Mounting Tool
hexagon wrench key 2 and 2.5, depending on the case.
M3 respectively.
to the M2.5 tapped portion of the lower part of switch mounting bracket's
concave part. (2 locations) Use caution to avoid the tip of a screw from
sticking out of the switch mounting bracket's bottom surface.
16
switch.
cap screw w into M3 tapped portion. (2 locations)
cylinder body, and then slide it to the detection position roughly.
secure the auto switch.
Hexagon socket head cap screw (M3 x 16
Cylinder series
MGP, MLGP
l
), then put it through the part of through-holes (2 locations) of an auto
Caution
Hexagon socket head cap screw (M2.5 x 8
Hexagon wrench key 2.5
BMG1-040
40
Hexagon wrench key 2
BMG1-040
Applicable bore size (mm)
l
50
)
BMG1-040
l
)
63
BMG1-040
Auto switch
80
l
) down lightly
6-16-67
BMG1-040
100
CJ1
CJP
CJ2
CM2
CG1
MB
MB1
CA2
CS1
C76
C85
C95
CP95
NCM
NCA
D-
-X
20-
Data