KDM20-07 SMC Corporation, KDM20-07 Datasheet - Page 2

• Manufacturer Part Number: KDM20-07
• Description: CONNECTOR, PNEUMATIC, 1/4IN. OD TUBE, 20 STATION, RECTANGULAR
• Manufacturer: SMC Corporation

Model
Model
Mixed Sizes of Plug Connectors and Socket Connectors
The rectangular multi-connector permits connector exchange in any desired position, thus
allowing use of different sizes of tubes.
Principal Parts Material
1. Loosen the cross-recessed head machine
No. of connection
Plug
connector
Socket
connector
(with packing)
screw by using a Phillips screwdriver to
remove the plate from the case.
Connector
Plug case, Socket case
Plate, Bracket
Plug connector,
Socket connector
Clamp bolt, Screw for bracket,
Cross-recessed head machine screw
Type E snap ring
tubes
10
20
Tubing
O.D.
ø3.2
ø3.2
Tubing
ø4
ø6
ø8
ø4
ø6
ø8
O.D.
ø3.2
ø3.2
ø4
ø6
ø8
ø4
ø6
ø8
Body
Chuck
Guide
Collet,
Release button
Seal
Cross-recessed round
head screw
KDMP-23
KDMP-04
KDMP-06
KDMP-08
KDMS-23
KDMS-04
KDMS-06
KDMS-08
KDM10P-23
KDM10P-04
KDM10P-06
KDM10P-08
KDM20P-23
KDM20P-04
KDM20P-06
KDM20P-08
Model
Plug
PBT, C3604BD Electroless nickel plated (ø8)
Model
2. After exchanging connectors in desired
release button
Plate
places, fix the plate to the case by using a
Phillips screwdriver.
Electroless nickel plated, POM (ø8)
Color of
Blue
Stainless steel 304, C3604BD
KDM10S-23
KDM10S-04
KDM10S-06
KDM10S-08
KDM20S-23
KDM20S-04
KDM20S-06
KDM20S-08
SWRM, Nickel plated
Socket
Stainless steel 304
Stainless steel 304
SPCC plated
Rectangular Multi-connector
POM
POM
NBR
Connector
release button
Color of
Blue
Case
Separation
Loosen the clamp bolt to separate the plug
side from the socket side.
Connection
Put together the irregular faces for engage-
ment and connect the plug case to the
socket. After tightening the clamp bolt by
hand, tighten it further with allen wrench
(nominal width across flats: 4).
Panel mounting
1. Loosen (4) screws for bracket on the
2. Shift the panel mounting bracket to the
3. After shifting the bolt for bracket to the out-
4. Loosen the screw for bracket until the
Allen wrench
(Nominal width across flats 4)
socket side using a Phillips screwdriver
(JIS nominal No. 2) until the bracket
touches the stop ring.
inside (Move the screw for bracket in the
longitudinal direction of the slot) and put
the connector in the panel mounting hole.
(Panel-mounting hole: See Dimensions.)
side, tighten the bolt by a Phillips screw-
driver to fix the socket case.
bracket touches the stop ring and shift the
bracket to the inside to remove the con-
nector from the panel.
Clamp bolt
Caution
Series
How to Use
Mounting
Irregular faces for
engagement
Phillips screwdriver
KDM
After loosening the screw,
shift the bracket to the inside.
Socket side
Plug side
Clamp bolt
15-2-107
Panel mounting
bracket
Shift the bolt to the
outside and tighten it.
Screw for
bracket
Panel
K„
M„
H„
D„
MS
T„
VMG