PS1000-R06L SMC Corporation, PS1000-R06L Datasheet - Page 2

• Manufacturer Part Number: PS1000-R06L
• Description: Air Checker
• Manufacturer: SMC Corporation

Trimmer
Pressure Switch Calibration
• Use the calibration adjustment to
• Rotate clockwise to increase pres-
• In the event of setting, use a flat
Rotation angle of the trimmer is 220°.
There is a stop provided to prevent the trimmer from rotating beyond its
limits. Rotation beyond the limit can damage the trimmer. Adjust the
trimmer gently within the rotation angle.
Internal Circuit/Wiring
Lead wire colors inside ( ) are those prior to conformity to IEC standards.
Circuit
Example of connection with a PLC (Sequence controller)
16-5-2
Series
Brown (Red)
Blue (Black)
set ON pressure.
sure setpoint. For setting vacuum,
rotate counterclockwise.
head screwdriver suited for the
groove of a trimmer, and rotate it
lightly with a finger tip.
10
11
Main circuit
Output specifications
of switch
Switch
PS
2-wire system (For positive pressure)
(For vacuum and residual pressure)
Pressure
PS1000 ON
PS1100 ON
(MPa)
220°
Input
COM
OFF
OFF
-0.1
0.4
0.2
2-wire system
PS1000/1100
0
Blue (Black)
Brown (Red)
OUT (–)
NPN
Source type
Input unit
OUT (+)
Load
Switch Specifications
00
How to Order
+
–
12 to 24 VDC
Left end adjustment limit
Setting pressure
t
Switch turns ON when the pressure is larger
than setting pressure.
Switch turns ON when the pressure is smaller
than setting pressure.
Blue (Black)
Brown (Red)
Main circuit
of switch
Switch
R06
vacuum
High
R06
Piping specifications
Input
COM
–
Right end adjustment limit
L
ø6 reducer
Lead wire length
L
Pressure
setting trimmer
Blue (Black)
Brown (Red)
PNP
Sink type
Input unit
OUT (–)
OUT (+)
Load
+
3 m
+
–
12 to 24 VDC
High
pressure
Dimensions
Specifications
Switch output
Max. operating
pressure
Regulating
pressure range
Fluid
Indication light
Temperature
characteristics
Repeatability
Hysteresis
Load voltage
Load current
Leakage
Int. voltage drop
Operating
temperature range
Insulation
resistance
Withstand voltage
Vibration
resistance
Impact resistance
Weight
Port size
Enclosure
Lead wire
Refer to pages 16-14-3 to 16-14-4 for Safety Instruc-
tions and Common Precautions on the products
mentioned in this catalog, and refer to pages 16-1-11
to 16-1-13 for Precautions on every series.
Caution
Model
10 to 500 Hz Pulse width 1.5 mm or acceleration 98 m/s
Present pres.≥Setting pres.: ON
–
Grommet oil-proof cabtire cord 2-wires ø2.55, 0.18 mm
980 m/s
(at the smaller vibration) in X, Y, Z directions (2 hours)
+
LED display
25.5
PS1000-R06L
PRESS. –0.10 to 45 MPa
–0.1 to 0.45 MPa
AIRCHECKER
PS1000-R06L
{–1 to 4.6 kgf/cm
30
MADE IN JAPAN
Calibration trimmer
Between external terminals and case
Between external terminals and case
2
12 to 24 VDC (Ripple ±10% or less)
X, Y, Z directions (3 times for each direction)
0 to 60°C (With no condensation)
2 MΩ (500 VDC by megameter)
1000 VAC 50/60 Hz for 1 min.
2
}
ON: When red LED turns on
ø6 reducer
5 g (Excluding lead wire)
Air/Non-corrosive gas
±3% F.S. or less
±1% F.S. or less
1 mA or less
5 to 40 mA
ø6 reducer
5 V or less
4% F.S.
1 MPa
IP40
Applicable One-touch fittings
KQ
Other Series KQ/KS
Series KJ
Series KJ (-X20)
Present pres.≤Setting pres.: ON
„Lead wire length
S Y
H L T
–0.1 to 0.4 MPa
PS1100-R06L
3000
06-M5
2
, 3 m
16
13
14.5
16
A
2