IS1000M-30-X207 SMC Corporation, IS1000M-30-X207 Datasheet - Page 2

• Manufacturer Part Number: IS1000M-30-X207
• Description: Switch, PRESSURE, PNEUMATIC, 0.1 - 0.4 MPA, 1 AMP OUT, 100V MAX. FOR AC25/30
• Manufacturer: SMC Corporation

Specifications of IS1000M-30-X207

• Adjustment Range: 0.1 to 0.4 MPa
• Current, Rating: 50 mA
• Length, Wire: 0.5 m (Standard)
• Pressure, Operating: 0.7 MPa (Max.)
• Repeatability: ± 0.05 MPa
• Size, Port: 1⁄8 in. NPT
• Temperature, Ambient: -5 to +60 °C
• Voltage, Rating: 100 V Max.
• Set Pressure Range (off): 0.1 to 0.4 MPa
• Maximum Operating Pressure: 0.7 MPa
• Ambient And Fluid Temperature: –5° to 60°C (with No Freezing)

16-9-2
Series
1. Connect load before connecting with power
2. In the case of induction load or lead wire ex-
Construction
3. Internal circuit of contact protection box
Be sure to read before handling. Refer to pages 16-14-3 and 16-14-4 for Safety Instructions and Common
Precautions on the products mentioned in this catalog, and refer to pages 16-1-11 to 16-1-13 for Precautions on
every series.
Surge
absorber
Condenser
source.
ceeding 5 m long, the following contact protec-
tion box should be used. It may lead to dam-
age to a switch.
Warning
CD-P11
CD-P12
Part no.
q
w
R
1
/
IS1000
CD-P11
Choke
coil
CD-P12
Choke
coil
Resistance
8
100 VAC
Voltage
24 VDC
Switch side: 0.5 m
Load side: 0.5 m
Brown
Blue
(+) Brown
(–) Blue
Lead wire length
23
Wiring
4. How to connect contact protection box
5. Dimensions of lead wire
1. When changing piping by hand, hold body.
2. Do not drop nor apply excessive force.
3. Tighten IS1000-01 applying the spanner on
4. Mounting direction is available in either
t
u
y
i
!0
o
e
r
Connect the lead wires from the body and the
contact
“SWITCH”. Lead wire should be as short as
possible, within 1 m.
Enclosure: ø 3.4
Insulator:
Conductor: ø 0.64
Electrical wire must not be subjected to exces-
sive force.
It may cause a malfunction or damage.
It may cause a malfunction or damage.
the PT fitting part.
horizontal or perpendicular.
Warning
Precautions
Mounting/Piping
protective
ø 1.1
0.2
0.4
IS1000
MPa
15
0.1
0.3
box
side
Component Parts
No.
indicated
q
w
e
r
t
y
u
i
o
!0
Shield plate
Switch assembly
Piston
PT fittings
Adjusting screw
Pointer
Spring
Scale plate
Miniseal Y type
Magnet
Description
1. Do not use with corrosive gases or fluids.
2. Never use in an environment where flamma-
3. Avoid use in vacuum applications.
1. Scale of switching set display is the set value
2. When detecting ON-pressure signal, note that
3. Pressure display on the scale plate is just as a
1. Avoid using a switch in a magnetic environ-
2. Do not use in such an environment, where
3. Avoid vibration. Vibration may cause malfunc-
ble fluid or gas is used. Since this is not an
explosion-proof construction, it may lead to an
explosive disaster.
Switch may be imploded.
at the pressure drop.
set pressure on scale plate plus ON-OFF differ-
ential (Hysteresis) will be ON-pressure signal.
reference guide. For an accurate setting,
measure it by pressure gauge.
ment. It may cause a malfunction.
water or oil is splashed. Since it is the open
type construction, if water or oil make an
ingress into the internal parts, the electric
circuit will be corroded and may result in a
malfunction or damage.
tion or may cause setting to be incorrect.
Warning
Warning
Operating Environment
Warning
Pressure Source
Pressure Setting
Stainless steel 304-WPB
Rigid vinyl chloride
Rare earth magnet
Rolled steel plate
Zinc die-casted
Polyacetal
Material
Brass
Brass
NBR
—