AFD40-N04D-Z SMC Corporation, AFD40-N04D-Z Datasheet - Page 2

• Manufacturer Part Number: AFD40-N04D-Z
• Description: Micro-Mist Separator; 150 PSI max; 1/2NPT ports; auto drain
• Manufacturer: SMC Corporation

Specifications of AFD40-N04D-Z

• Body Size: 40 in.
• Diameter: 70 mm
• Height: 165 mm
• Material, Bowl: Polycarbonate
• Pressure, Operating: 1.0 MPa (Max.)
• Proof Pressure: 1.5 MPa
• Size, Port: 1⁄2 in.
• Temperature, Ambient: -5 to +60 °C
• Thread Type: NPT
• Operating Pressure: 150 PSI

AFD20/30/40
33
Flow Characteristics
Construction
Note 1) Including O-Ring. Contact SMC regarding the bowl assembly supply for PSI and °F unit specifications.
Note 2) Bowl assembly for AFD30 to AFD40-06 includes a bowl guard (steel band material).
AFD20
AFD30, 40
Parts list
Replacement parts
No.
No.
AFD 20
2
3
4
1
Description
Element assembly
Bowl assembly
Bowl O-ring
Body
IN
Description
IN
Flow rate L/min (ANR)
Drain
Drain
Zinc die-cast
AFD20
Note 1)
ø10 One-touch fitting
OUT
Material
q
r
w
e
NBR
OUT
PC
q
r
w
e
(Representative values)
AFD30, AFD40, AFD40-06
Material
AFD20P-060AS
C2SFP-260S
Aluminum die-cast
AFD20
C2SF
N.C.
Float type auto drain (N.C.)
ø10 One-touch fitting
Float type auto drain
AFD30P-060AS
C3SF
C3SFP-260S
AFD 30
AFD30
M5 x 0.8
Note 2)
Part no.
AFD40P-060AS
C4SF
C4SFP-260S
AFD40
N.O.
Flow rate L/min (ANR)
Platinum silver
Note 2)
Note
AFD40P-060AS
C4SF
C4SFP-260S
AFD40-06
Note 2)
1. Install a mist separator (Series AFM) as a
2. Do not install on the inlet side of the dryer as
1. Replace the element every 2 years or when the
1. Design the system so that the mist separator is
1. Do not allow air flow that exceeds the rated flow.
2. Do not use in a low pressure application (such
Be sure to read before handling.
Refer to pages 75 through 78 for safety
instructions and F.R.L. unit precautions.
preliminary filter on the inlet side of the micro-
mist separator to prevent premature clogging.
this can cause premature clogging of the
element.
pressure drops becomes 0.1MPa, whichever
comes first, to prevent damage to the element.
installed in a pulsation-free location. The
difference between internal and external
pressure inside the element should be kept
within 0.1MPa, as exceeding this value could
cause damage.
If the air flow is allowed outside the range of the
rated flow even momentarily, drainage and
lubricant may splash at the outlet side or cause
damage to the component.
as a blower). F.R.L. unit has its own minimum
operating pressure depending on the equipment
and is designed specifically to function with
compressed air. If used below the minimum
operating pressure, a loss of performance and
malfunction can occur. Contact SMC if an
application under such conditions cannot be
avoided.
Caution
Warning
Caution
Caution
Specific Product Precautions
AFD 40
Maintenance
Air Supply
Selection
Design
Flow rate L/min (ANR)
: When saturated with oil
: Initial state