ADP2147ACBZ-110-R7 Analog Devices Inc, ADP2147ACBZ-110-R7 Datasheet - Page 14

• Manufacturer Part Number: ADP2147ACBZ-110-R7
• Description: IC REG BUCK 800MA 3MHZ 6WLSCP
• Manufacturer: Analog Devices Inc
• Series: -r
• Type: Step-Down (Buck), PWM - Current Moder

Specifications of ADP2147ACBZ-110-R7

• Internal Switch(s): Yes
• Synchronous Rectifier: Yes
• Number Of Outputs: 1
• Voltage - Output: 1.275V, 0.981V
• Current - Output: 800mA
• Frequency - Switching: 3MHz
• Voltage - Input: 2.3 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 6-UFBGA, WLCSP
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: ADP2147ACBZ-110-R7TR

ADP2147
Capacitors with lower equivalent series resistance (ESR) are
preferred to guarantee low output voltage ripple, as shown in
the following equation:
The effective capacitance needed for stability, which includes
temperature and dc bias effects, is 3 μF.
Table 7. Suggested 4.7 μF Capacitors
Vendor
Murata
Taiyo Yuden
TDK
Input Capacitor
Higher value input capacitors help to reduce the input voltage
ripple and improve transient response. Maximum input
capacitor current is calculated using the following equation:
To minimize supply noise, place the input capacitor as close to
the VIN pin of the ADP2147 as possible. As with the output
capacitor, a low ESR capacitor is recommended. The list of
recommended capacitors is shown in Table 8.
Table 8. Suggested 4.7 μF Capacitors
Vendor
Murata
Taiyo Yuden
TDK
THERMAL CONSIDERATIONS
Because of the high efficiency of the ADP2147, only a small
amount of power is dissipated inside the ADP2147 package, which
reduces thermal constraints of the design.
However, in applications with maximum loads at high ambient
temperature, low supply voltage, and high duty cycle, the heat
dissipated in the package is high enough that it may cause the
junction temperature of the die to exceed the 125°C maximum.
If the junction temperature exceeds 150°C, the converter enters
ESR
I
CIN
COUT
≥
I
LOAD
≤
Type
X5R
X5R
X5R
Type
X5R
X5R
X5R
V
I
(
MAX
RIPPLE
RIPPLE
)
V
Model
GRM188R60J475
JMK107BJ475
C1608X5R0J475
Model
GRM188R60J475
JMK107BJ475
C1608X5R0J475
OUT
(
V
V
IN
IN
−
V
OUT
)
Case
Size
0603
0603
0603
Case
Size
0603
0603
0603
Voltage
Rating (V)
6.3
6.3
6.3
Voltage
Rating (V)
6.3
6.3
6.3
Rev. 0 | Page 14 of 16
thermal shutdown. The regulator recovers when the junction
temperature falls below 130°C.
The junction temperature of the die is the sum of the ambient
temperature of the environment and the temperature rise of the
package due to power dissipation, as shown in the following
equation:
where:
T
T
T
dissipation.
The package’s rise in temperature is directly proportional to the
power dissipation in the package. The proportionality constant
for this relationship is the thermal resistance from the junction
of the die to the ambient temperature, as shown in the following
equation:
where:
T
θ
ambient temperature of the package.
P
PCB LAYOUT GUIDELINES
Poor layout can affect the ADP2147 performance, causing EMI
and electromagnetic compatibility problems, ground bounce,
and voltage losses. Poor layout can also affect regulation and
stability. To implement a good layout, use the following rules:
•
•
•
•
JA
D
J
A
R
R
is the junction temperature.
is the ambient temperature.
is the rise in temperature of the package due to power
is the rise in temperature of the package.
is the power dissipation in the package.
is the thermal resistance from the junction of the die to the
T
T
Place the inductor, input capacitor, and output capacitor
close to the IC using short tracks. These components carry
high switching frequencies, and large tracks act as antennas.
Route the output voltage path away from the inductor and
SW node to minimize noise and magnetic interference.
Maximize the size of ground metal on the component side
to help with thermal dissipation.
Use a ground plane with several vias connecting to the com-
ponent side ground to further reduce noise interference on
sensitive circuit nodes.
J
R
= T
= θ
A
JA
+ T
× P
R
D