5962-8606310XA STMicroelectronics, 5962-8606310XA Datasheet - Page 4

• Manufacturer Part Number: 5962-8606310XA
• Manufacturer: STMicroelectronics

Specifications of 5962-8606310XA

• Lead Free Status / Rohs Status: Supplier Unconfirmed

DSCC FORM 2234
APR 97
MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The
modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for
device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified
herein.
MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M.
in screening (see 4.2 herein) or qualification conformance inspection, groups A, B, or C (see 4.4), the devices shall be
programmed by the manufacturer prior to test. A minimum of 50 percent of the total number of cells shall be programmed.
electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full
case operating temperature range.
tests for each subgroup are defined in table I.
marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer
has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator shall still be
marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be
in accordance with MIL-PRF-38535, appendix A.
MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A.
manufacturer prior to delivery.
specified in 4.5.
procedures and characteristics specified in 4.6.
pattern or erased. As a minimum, verification shall consist of performing a functional test (subgroup 7) to verify that all bits are in
the proper state. Any bit that does not verify to be in the proper state shall constitute a device failure and shall be removed from
the lot.
listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of
compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see
6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this
drawing shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and
herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in
3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.2.3 Truth table(s). The truth table shall be as specified on figure 3.
3.2.3.1 Unprogrammed devices. The truth table for unprogrammed devices shall be as specified on figure 3. When required
3.2.3.2 Programmed devices. The requirements for supplying programmed devices are not a part of this drawing.
3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical
3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be
3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in
3.6 Processing EPROMS. All testing requirements and quality assurance provisions herein shall be satisfied by the
3.6.1 Erasure of EPROMS. When specified, devices shall be erased in accordance with the procedures and characteristics
3.6.2 Programmability of EPROMS. When specified, devices shall be programmed to the specified pattern using the
3.6.3 Verification of state of EPROMS. When specified, devices shall be verified as either programmed to the specified
3.7 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535
DEFENSE SUPPLY CENTER COLUMBUS
MICROCIRCUIT DRAWING
COLUMBUS, OHIO 43218-3990
STANDARD
SIZE
A
REVISION LEVEL
H
SHEET
5962-86063
4