BTS441R Infineon Technologies, BTS441R Datasheet
BTS441R
Specifications of BTS441R
Available stocks
Related parts for BTS441R
BTS441R Summary of contents
Page 1
... Open load detection in OFF-state • Feedback of thermal shutdown in ON-state Data sheet Package TO-263-5 20mΩ V bb(on) 4.75 ... 41V I L(ISO) 21A I L(lim) 65A ® technology. 1 TO-220-5-12 SMD Straight Vbb IN Logic with protection ST functions PROFET GND Rev. 1.1, 2009-01-30 BTS441R OUT Load ...
Page 2
... Data sheet PROFET 2 BTS441R Rev. 1.1, 2009-01-30 ...
Page 3
... GND pin, e.g. with a 150 Ω bb(AZ) 2 (one layer, 70μm thick) copper area for Symbol Values Load dump I self-limited L T -40 ...+150 j T -55 ...+150 stg P 125 tot 2 1.0 ESD 4.0 8.0 V -10 ... +16 IN ±2 ±5 ≤ thJC ≤ thJA ≤ 33 Rev. 1.1, 2009-01-30 BTS441R Unit ° K/W ...
Page 4
... T =-40° bb(AZ) T =+25...+150° =-40...+25° bb(off) T =+105° =+150° L(off) bb(off GND >5 Values min typ max -- 200 40 110 250 0 V/μ V/μs off Rev. 1.1, 2009-01-30 BTS441R Unit mΩ μ μA μA mA ...
Page 5
... Data sheet Symbol =-40° L(lim) =25° =+150° L(SCr) =25° j,start off(SC) =-40° =25..150° ON(CL Δ 13 > ON(rev) OUT bb =+150° (one layer, 70μm thick) copper area for BTS441R Values Unit min typ max -- -- 150 -- -- ° 540 -- mV ...
Page 6
... Z = high impedance, potential depends on external circuit Status signal valid after the time delay shown in the timing diagrams 6 Values min typ max 2.5 3.8 6.5 1.2 -- 2.2 0 0.3 -- IN( 4 500 5.4 6 0.4 OUT 16 Rev. 1.1, 2009-01-30 BTS441R Unit V kΩ μA μA μs V ...
Page 7
... In case of reverse battery the load current has to be limited by the load. Temperature protection is not active Open-load detection OFF-state diagnostic condition: Open Load OUT < 375 Ω ST(ON) GND disconnect t in Any kind of load. In case of Input=high BTS441R = 150 Ω typ., R GND Z2 > typ.; IN low ≈ OUT IN IN(T+) Rev. 1.1, 2009-01-30 ...
Page 8
... While demagnetizing load inductance, the energy dissipated in PROFET ON(CL) with an approximate solution for R L > 0 Ω: · OUT(CL · L Maximum allowable load inductance for a single switch off / j,start = 150° Ω L [mH] 8 BTS441R ^ · i (t) dt, L · ( OUT(CL [A] Rev. 1.1, 2009-01-30 ...
Page 9
... Typ. on-state resistance high L R [mΩ] ON Typ. standby current , I RII M = 9...34 V, IN1,2 = low bb I [μA] bb(off) Data sheet V [ [° BTS441R Rev. 1.1, 2009-01-30 ...
Page 10
... Figure 2a: Switching a resistive load, turn-on/off time and slew rate definition: on Data sheet Figure 2b: Switching a lamp, Figure 3a: Short circuit shut down by overtemperature, reset by cooling off Heating up may require several milliseconds, depending on external conditions 10 BTS441R Rev. 1.1, 2009-01-30 ...
Page 11
... Figure 4a: Overtemperature: Reset if T < Figure 5a: Open load: detection in OFF-state, turn on/off to open load 500µs ST delay Open load detection requires an external pull up resistor between OUT and V BB Data sheet 11 BTS441R Rev. 1.1, 2009-01-30 ...
Page 12
... Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020). For further information on alternative packages, please visit our website: http://www.infineon.com/packages. Data sheet 10 ±0.2 A 9.9 ±0.2 1) 8.5 3.7 -0. 0.8 ±0 1.7 0. 4.4 1.27 ±0.1 0.05 2.4 0.5 ±0.1 2.4 C Dimensions in mm Rev. 1.1, 2009-01-30 BTS441R ...
Page 13
... Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020). For further information on alternative packages, please visit our website: http://www.infineon.com/packages. Data sheet 10 ±0 8.5 0...0. 1.7 0. 4.4 1.27 ±0.1 B 0.05 2.4 0.1 0.1 B GPT09062 Dimensions in mm Rev. 1.1, 2009-01-30 BTS441R ...
Page 14
... Date Changes 1.1 2009-01-30 RoHS-compliant PG-TO220 and PG-TO263 packages version of the BTS441R All pages: Infineon logo updated Page 1: Added “AEC Qualified” and “RoHS” logo, added “Green Product (RoHS compliant)” and “AEC Qualified” statement to feature list, package names changed to RoHS compliant versions, updated package drawing ...
Page 15
... Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life ...