SC2614MLTR Semtech, SC2614MLTR Datasheet
SC2614MLTR
Specifications of SC2614MLTR
Available stocks
Related parts for SC2614MLTR
SC2614MLTR Summary of contents
Page 1
... High speed data line termination 10k 10k Cin 10k 16 9 12VCC 5VCC 4 15 5VSBY BF_CUT PWRGD PGND 18 7 SS/EN VDDQSTBY 17 8 COMP VDDQIN 12 1 AGND LGND VTT 2 5 VTTSNS VTT THPAD 19 SC2614 1 SC2614 With BF_CUT and PGOOD ® 1uF L 0.1uF Cout VTT 0.1uF www.semtech.com VDDQ ...
Page 2
... Exceeding the specifications below may result in permanent damage to the device, or device malfunction. Operation outside of the parameters specified in the Electrical Characteristics section is not implied See Mounting Considerations. Electrical Characteristics Unless specified 25°C, 12VCC = 12V, 5VCC = 5V, 5VSBY = 5V © 2004 Semtech Corp θ θ STG SC2614 www.semtech.com ...
Page 3
... POWER MANAGEMENT Electrical Characteristics (Cont.) Unless specified 25°C, 12VCC = 12V, 5VCC = 5V, 5VSBY = 5V © 2004 Semtech Corp ∆ ∆ ∆ ∆ SC2614 www.semtech.com ...
Page 4
... VDDQIN 8 11 5VCC 9 10 (18 Pin MLP) Note: Pin19 is the thermal Pad on the bottom of the device Pin Descriptions © 2004 Semtech Corp. Ordering Information S SS/EN Notes: COMP (1) Only available in tape and reel packaging. A reel 12VCC contains 3000 devices PGND AGND BF_CUT PWRGD ...
Page 5
... POWER MANAGEMENT Timing Diagram © 2004 Semtech Corp. 5 SC2614 www.semtech.com ...
Page 6
... POWER MANAGEMENT Block Diagram © 2004 Semtech Corp. 6 SC2614 www.semtech.com ...
Page 7
... Io (A) VDDQ Load Regulation 1.0% 0.5% 0.0% -0.5% -1.0% -2.5 -2.0 -1.5 -1.0 -0.5 0.0 Io (A) VTT Load Regulation, Source and Sink © 2004 Semtech Corp. 100% 80% 60% 40% 20% 0% 1.2 100E+3 1E+6 VCOMP vs Duty Cycle 8.0 10.0 12.0 0.5 1.0 1 ...
Page 8
... PWR GD/S5 18 SS/EN J12 17 COMP SS/EN 12 AGND R6 TBD 3 LGND C10 2 VTTSN C11 TBD C12 0.1uF TBD J14 GND J19 ATX M/B MOLEX 39-29-9202 Figure 2: Evaluation Board Schematic © 2004 Semtech Corp 12V R2 10k 1500uF 1500uF 1500uF 1uF R3 2.2 9 5VCC 2 SGND 7 VDDQSBY ...
Page 9
... POWER MANAGEMENT Applications Information Description The Semtech SC2614 DDR power supply controller is the latest and most complete, three in one, switching and linear regulator, providing the necessary functions to comply with S3 and S5 sleep state signals generated by the Desktop Computer Motherboards. The SC2614 BF_CUT ...
Page 10
... © 2004 Semtech Corp. The compensation network includes a resistor and a ca- pacitor in series, which terminates from the output of the error amplifier to the ground. This device uses voltage mode control with input voltage feed forward. The peak-to-peak ramp voltage is propor- tional to the input voltage, which results in an excellent performance to reject input voltage variation ...
Page 11
... Mathcad. The phase margin can then be checked using the Bode plot. Usually, this design procedure ensures a healthy phase margin. An example is given below to demonstrate the proce- dure introduced above. The parameters of the power supply are given as: © 2004 Semtech Corp. ⎛ ⎞ ⎛ ⎞ F ...
Page 12
... POWER MANAGEMENT 100 50 mag phase 135 180 10 © 2004 Semtech Corp. Loop Gain Mag (dB 100 F i Loop Gain Phase (Degree 100 F i Fig. 2. Bode plot of the loop 12 SC2614 www.semtech.com ...
Page 13
... PC board area for effective heatsinking. The copper area immdiately surrounding the thermal pad connection must not be interupted by routing traces. © 2004 Semtech Corp. Exposed Pad Stencil Design It is good practice to minimize the presence of voids within the exposed pad inter-connection. Total elimination is ...
Page 14
... POWER MANAGEMENT Outline Drawing - MLP-18 TERMINAL 1 TOP VIEW IDENTIFIER TERMINAL 1 BOTTOM VIEW 1 CONTROLLING DIMENSIONS: MILLIMETERS © 2004 Semtech Corp. 14 SC2614 www.semtech.com ...
Page 15
... POWER MANAGEMENT Land Pattern - MLP-18 Contact Information © 2004 Semtech Corp. Semtech Corporation Power Management Products Division 200 Flynn Road, Camarillo, CA 93012 Phone: (805)498-2111 FAX (805)498-3804 15 SC2614 www.semtech.com ...