ATA5824-PLQW 80 Atmel, ATA5824-PLQW 80 Datasheet - Page 74

• Manufacturer Part Number: ATA5824-PLQW 80
• Manufacturer: Atmel

Specifications of ATA5824-PLQW 80

• Operating Temperature (min): -40C
• Operating Temperature (max): 105C
• Operating Temperature Classification: Industrial
• Product Depth (mm): 7mm
• Product Height (mm): 0.9mm
• Product Length (mm): 7mm
• Operating Supply Voltage (typ): 5V
• Lead Free Status / Rohs Status: Compliant

17. Electrical Characteristics: General (Continued)
All parameters refer to GND and are valid for T
V
f
can be found in the specific sections of the “Electrical Characteristics”.
74
*) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter
Note:
RF
2.10
2.11 System noise figure
2.12 Intermediate frequency
VS2
No. Parameters
2.7 RSSI output
2.8
2.9
= 433.92 MHz (battery application) unless otherwise specified. Details about current consumption, timing and digital pin properties
= 4.4V to 5.6V, V
Output resistance RSSI
pin
Maximum frequency
offset in FSK mode
Supported FSK
frequency deviation
1. Pin numbers in brackets mean they were measured with RF_IN matched to 50 according to
ATA5823/ATA5824
component values according to
page 22
VSINT
with component values according to
= 4.4V to 5.25V (car application). Typical values are given at V
Test Conditions
Dynamic range
Lower level of range
f
f
f
Upper level of range
f
f
f
Gain
Output voltage range
RX mode
TX mode
Maximum frequency
difference of f
receiver and transmitter in
FSK mode (f
frequency of the FSK signal
with
f
P
P
(see
With up to 2 dB
loss of sensitivity.
Note that the tolerable
frequency offset is for
f
lower than for
f
f
f
f
f
f
f
RF
RF
RF
RF
RF
RF
DEV
DEV
DEV
RF
RF
RF
RF
RF
RF
f
RF_IN
RF_IN
OFFSET2
= 315 MHz
= 433.92 MHz
= 868.3 MHz
= 315 MHz
= 433.92 MHz
= 868.3 MHz
= 315 MHz
= 433.92 MHz
= 868.3 MHz
= 315 MHz
= 433.92 MHz
= 868.3 MHz
= ±19.5 kHz)
= ±28 kHz, 8.5 kHz
= ±19.5 kHz hence
Figure 7-2 on page
+10 dBm
P
RFIN_High
= ±66.5 kHz
RF
Table 7-2 on page 12
RF
amb
is the center
between
= –40°C to +105°C, V
12)
Table 7-7 on page 22
(4), 36
(4), 36
(4), 36
(4), 36
(4), 36
Pin
36
(4)
(4)
(4)
(4)
(4)
(1)
(RF
IN
VS1
) and RF_OUT matched to 50 according to
P
P
Symbol
OV
= V
RFIN_High
f
f
RFIN_Low
D
R
OFFSET1
OFFSET2
f
NF
NF
NF
DEV
RSSI
RSSI
f
f
f
IF
IF
IF
RSSI
VS2
(RF
= V
OUT
VSINT
).
Min.
VS1
350
–69
–75
±14
5.5
32
8
= 2.15V to 3.6V (battery application), and
= V
VS2
= V
±19.5
–116
–115
–112
Typ.
–46
–45
–42
227
223
226
8.0
5.5
6.5
9.7
70
10
40
VSINT
Figure 7-1 on page 11
= 3V and T
Max.
1100
10.5
12.5
+69
+75
±28
50
Figure 7-12 on
amb
4829D–RKE–06/06
mV/dB
dBm
dBm
dBm
dBm
dBm
dBm
Unit
kHz
kHz
kHz
kHz
kHz
mV
dB
dB
dB
dB
k
= 25°C,
Type*
with
A
A
A
A
A
C
B
B
B
B
B
A
A
A