TB2132FNG(O,EL) Toshiba, TB2132FNG(O,EL) Datasheet

no-image

TB2132FNG(O,EL)

Manufacturer Part Number
TB2132FNG(O,EL)
Description
Manufacturer
Toshiba
Datasheet

Specifications of TB2132FNG(O,EL)

Lead Free Status / Rohs Status
Supplier Unconfirmed
3-V AM/FM/TV Single Chip Tuner IC with On-Chip PLL
The TB2132FNG is an IC suitable for 3-V headphone radio and
radio cassette application. It has FM/TV front end, FM IF, FM
stereo decoder, AM function and PLL function on a single chip.
The FM/TV front end is designed to lower the oscillation voltage
of the FM/TV local oscillator, enabling this IC to meet the new
FCC standards.
Features
Low supply current (V
FM: I
AM: I
Operating supply voltage range
Tuner block
• Can be used for TV band.
• Enable to meet the new FCC standards.
• Adjustment-free FM quad detector due to ceramic discriminator
• On-chip FM MPX VCO circuit
PLL block
• Reference frequency: 1 kHz , 1.5625 kHz, 3 kHz, 3.125 kHz, 5 kHz, 6.25 kHz, 12.5 kHz, 25 kHz
• Data transfer is performed with synchronous three-line bus, using pins CE (Chip Enable), CK (Clock) and
• Crystal oscillation frequency: 75 kHz
• IF count method: On-chip 20-bit counter
Note: The TB2132FNG is mounted with lead-free soldering alloys.
Pin 26 (FM/TV OSC) is sensitive to electrostatic discharge. Take care when handling.
: V
DATA (DATA).
CC
CC
CC
= 1.8 to 5.5 V (Ta = 25°C)
= 18 mA (typ.)
= 7.5 mA (typ.)
CC
TOSHIBA Bi-CMOS Integrated Circuit Silicon Monolithic
= 3 V, Ta = 25°C)
TB2132FNG
1
Weight: 0.17 g (typ.)
TB2132FNG
2006-04-11

Related parts for TB2132FNG(O,EL)

TB2132FNG(O,EL) Summary of contents

Page 1

... TOSHIBA Bi-CMOS Integrated Circuit Silicon Monolithic 3-V AM/FM/TV Single Chip Tuner IC with On-Chip PLL The TB2132FNG suitable for 3-V headphone radio and radio cassette application. It has FM/TV front end, FM IF, FM stereo decoder, AM function and PLL function on a single chip. The FM/TV front end is designed to lower the oscillation voltage of the FM/TV local oscillator, enabling this IC to meet the new FCC standards ...

Page 2

Block Diagram FM/TV RFout RFout V RFin OSC OSC AM MIX 1 FM/TV FM MIX RF AGC FM/TV GND MIX AGC FM RF ...

Page 3

Pin Description 1. Tuner Block Pin Characteristics No. 1 FM/TV RFin 2 GND 3 MIX OUT 4 AGC for FM IF and MPX) CC Internal Circuit GND 2 ⎯ ...

Page 4

Pin Characteristics No QUOD GND DET OUT GND 10 MPX IN Internal Circuit 7 GND kΩ 10 GND 2 4 TB2132FNG ...

Page 5

Pin Characteristics No. LPF1 • LPF pin for synchronous 11 detector LPF2 12 • LPF pin for phase detector 13 L-OUT 14 R-OUT 25 AM OSC Internal Circuit 11 DC AMP 2 GND 12 2 GND 13, ...

Page 6

Pin Characteristics No. 26 FM/TV OSC 27 AM RFin for FM RF OUT Refer to the internal circuit of pin RFout Refer to the internal circuit of pin ...

Page 7

PLL Block Pin No. Symbol Pin Name 15 XOUT Crystal oscillator pin 16 XIN Power supply 17 PLL GND input pin General-purpose OUT1 18 output port (ST) (ST port) General-purpose OUT2 19 output port (DO2) (DO output) Phase 20 ...

Page 8

... If you need adjust parameter values to compensate for variables in layout, ask Toshiba. Please use a crystal oscillator with lower CI value Toshiba tested a crystal oscillator from DAISHINKU CORP. (CI value is 30 kΩ max) using a Toshiba evaluation board. (for stages of AM and MPX) and RF V ...

Page 9

Miscellaneous 1) We offer information on software programs to control the TB2132FNG on Windows 95/98. For details, contact us. (Also contact us if you are using Windows 2000/NT offer an interface board to run the TB2132FNG under ...

Page 10

Configuration of Local Oscillator and Programmable Counter Operate the FM/TV local oscillator at approximately 200 MHz and select the counter input using the following settings of the bits. Then determine reference frequency and minimum step frequency. FM/TV OSC To MIX ...

Page 11

Serial Transfer Format Data input mode ( high-impedance state at input.) OUT CE 0.5 µs min 1 µs min CK Can be omitted. 0.5 µs min DATA “ “ “ “ A0 Can be omitted. Input address Internal ...

Page 12

Data in Detail • 16: N (divisor data P0: LSB, P16: MSB) • OUT1, 2: When set, a high appears on the OUT pin. When cleared, a low appears on the OUT pin. • BAND ...

Page 13

Input Mode Address Reset values • MO/ST : When cleared Auto Mode. When set Forced Monaural Mode. • When cleared, ...

Page 14

Output Mode * * * * Address • 19: General-purpose count data (C0: LSB, C19: MSB) • OVER: Set 1 when the measured value of general-purpose count data exceeds 20 bits. • BUSY: When read, ...

Page 15

Coil Data Test L Coil No. Frequency (µH) ⎯ 100 MHz 1 ⎯ 100 MHz 2 ⎯ OSC 100 MHz OSC 796 kHz 268 1 ⎯ ...

Page 16

Electrical Characteristics 1. Tuner Block (Unless otherwise specified 25° Characteristics Supply current FM input limiting voltage F/E TV input limiting voltage Input limiting voltage Recovered output voltage Signal to noise ratio FM IF Total harmonic distortion ...

Page 17

Characteristics ON Stereo sensitivity OFF Stereo hysteresis MPX Capture challenge Signal noise ratio Muting attenuation Unless otherwise specified 25° PLL Block ( Characteristics Operating supply voltage range Memory retention voltage range Operating supply current Memory retention ...

Page 18

DO at Pin 20 Characteristics Symbol High level I OH1 Output current Low level I OL1 Output OFF-leak current I DO2 at Pin 19 Characteristics Symbol High level I OH1 Output current Low level I OL1 Output OFF-leak current I ...

Page 19

TB2132FNG Test Circuit 2 RFin 0.022 µF 2 kΩ Vin 0.1 µ RFout RFout FM/ GND 1 2 TV/FM RFin 4700 pF 75 Ω Vin TV/FM IFin 270 Ω 50 Ω Vin ...

Page 20

Application Circuit V range RFout RFout V FM/ GND 1 2 ANT GND Vtune 3.3 k Ω Ω Power ...

Page 21

Application Circuit (for FM module) FM/ RFout RFout FM/ GND 1 2 ANT GND Vtune 3.3 k Ω Ω Power 390 Ω 10 µ ...

Page 22

Package Dimensions Weight: 0.17 g (typ.) 22 TB2132FNG 2006-04-11 ...

Page 23

... TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property ...

Related keywords