XC3S100E-5TQ144C Xilinx Inc, XC3S100E-5TQ144C Datasheet - Page 32

• Manufacturer Part Number: XC3S100E-5TQ144C
• Description: FPGA Spartan®-3E Family 100K Gates 2160 Cells 657MHz 90nm (CMOS) Technology 1.2V 144-Pin TQFP
• Manufacturer: Xilinx Inc

Specifications of XC3S100E-5TQ144C

• Package: 144TQFP
• Family Name: Spartan®-3E
• Device Logic Cells: 2160
• Device Logic Units: 240
• Device System Gates: 100000
• Number Of Registers: 1920
• Maximum Internal Frequency: 657 MHz
• Typical Operating Supply Voltage: 1.2 V
• Maximum Number Of User I/os: 108
• Ram Bits: 73728
• Re-programmability Support: Yes

Functional Description
Initialization
The CLB storage elements are initialized at power-up, dur-
ing configuration, by the global GSR signal, and by the indi-
vidual SR or REV inputs to the CLB. The storage elements
can also be re-initialized using the GSR input on the
STARTUP_SPARTAN3E primitive. See
(STARTUP_SPARTAN3E).
Table 17: Slice Storage Element Initialization
32
SR
REV
GSR
Signal
Set/Reset input. Forces the storage element
into the state specified by the attribute SRHIGH
or SRLOW. SRHIGH forces a logic “1” when SR
is asserted. SRLOW forces a logic “0”. For each
slice, set and reset can be set to be
synchronous or asynchronous.
Reverse of Set/Reset input. A second input
(BY) forces the storage element into the
opposite state. The reset condition is
predominant over the set condition if both are
active. Same synchronous/asynchronous
setting as for SR.
Global Set/Reset. GSR defaults to active High
but can be inverted by adding an inverter in
front of the GSR input of the
STARTUP_SPARTAN3E element. The initial
state after configuration or GSR is defined by a
separate INIT0 and INIT1 attribute. By default,
setting the SRLOW attribute sets INIT0, and
setting the SRHIGH attribute sets INIT1.
Description
Global Controls
www.xilinx.com
Distributed RAM
For additional information, refer to the “Using Look-Up
Tables as Distributed RAM” chapter in UG331.
The LUTs in the SLICEM can be programmed as distributed
RAM. This type of memory affords moderate amounts of
data buffering anywhere along a data path. One SLICEM
LUT stores 16 bits (RAM16). The four LUT inputs F[4:1] or
G[4:1] become the address lines labeled A[4:1] in the
device model and A[3:0] in the design components, provid-
ing a 16x1 configuration in one LUT. Multiple SLICEM LUTs
can be combined in various ways to store larger amounts of
data, including 16x4, 32x2, or 64x1 configurations in one
CLB. The fifth and sixth address lines required for the
32-deep and 64-deep configurations, respectively, are
implemented using the BX and BY inputs, which connect to
the write enable logic for writing and the F5MUX and
F6MUX for reading.
Writing to distributed RAM is always synchronous to the
SLICEM clock (WCLK for distributed RAM) and enabled by
the SLICEM SR input which functions as the active-High
Write Enable (WE). The read operation is asynchronous,
and, therefore, during a write, the output initially reflects the
old data at the address being written.
The distributed RAM outputs can be captured using the
flip-flops within the SLICEM element. The WE write-enable
control for the RAM and the CE clock-enable control for the
flip-flop are independent, but the WCLK and CLK clock
inputs are shared. Because the RAM read operation is
asynchronous, the output data always reflects the currently
addressed RAM location.
A dual-port option combines two LUTs so that memory
access is possible from two independent data lines. The
same data is written to both 16x1 memories but they have
independent read address lines and outputs. The dual-port
function is implemented by cascading the G-LUT address
lines, which are used for both read and write, to the F-LUT
write address lines (WF[4:1] in
ing the G-LUT data input D1 through the DIF_MUX in
Figure 15
vides a 16x1 dual-port memory as shown in
Any write operation on the D input and any read operation
on the SPO output can occur simultaneously with and inde-
pendently from a read operation on the second read-only
port, DPO.
and to the D1 input on the F-LUT. One CLB pro-
DS312-2 (v3.8) August 26, 2009
Figure
Product Specification
15), and by cascad-
Figure
26.
R