77052022A Intersil, 77052022A Datasheet
77052022A
Specifications of 77052022A
Available stocks
Related parts for 77052022A
77052022A Summary of contents
Page 1
LTR G Add case outline 2. Electrical changes in table I, 1.3, and 1.4. Editorial changes throughout. Change vendor CAGE 34371 vendor PINs and add vendor CAGE 24355. Delete vendor CAGE 32293 and add vendor CAGE 1ES66. H Changes in ...
Page 2
SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 77052 ...
Page 3
Absolute maximum ratings – continued. Storage temperature range ..................................................... -65°C to +150°C Power dissipation ( Case 2 ................................................................................. 1. Case E ................................................................................ 470 Case F and X ...................................................................... 725 mW at ...
Page 4
Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a ...
Page 5
Test Symbol I Input leakage current Leakage current into the +I S(OFF) source terminal of an “OFF” switch -I S(OFF) Leakage current into the +I D(OFF) drain terminal of an “OFF” switch -I D(OFF) Leakage current ...
Page 6
TABLE I. Electrical performance characteristics – continued. Test Symbol C Capacitance: Address A Capacitance: output switch Capacitance: input switch IS V Charge transfer error CTE V Single channel isolation ISO Crosstalk between V CT channels Break-before-make time ...
Page 7
TABLE I. Electrical performance characteristics – continued. Test Symbol Positive input clamping V IC(POS) voltage Negative input clamping V IC(NEG) voltage I Input leakage current Leakage current into the +I S(OFF) source terminal of an “OFF” ...
Page 8
TABLE I. Electrical performance characteristics – continued. Test Symbol +R Switch “ON” resistance DS1 -R DS1 Difference in switch “ON” +∆R resistance between DS1 channels -∆R DS1 C Capacitance: Address A Capacitance: output C OS switch Capacitance: input C IS ...
Page 9
TABLE I. Electrical performance characteristics – continued. Test Symbol I Input leakage current S(OFF) Leakage current into the source terminal of an “OFF” switch Leakage current into the +I D(OFF) drain terminal of an “OFF” ...
Page 10
TABLE I. Electrical performance characteristics – continued. Test Symbol R Switch “ON” resistance DS1 Switch “ON” resistance R DS2 C Capacitance: Address A Capacitance: output C OS switch Capacitance: input C IS switch Charge transfer error V CTE V Single ...
Page 11
Case outlines Device types Terminal number STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR ...
Page 12
NOTE: Input pulse requirements: V GEN FIGURE 3. Break before make test circuit and waveforms. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 ≤ THL(1) ...
Page 13
NOTE: Input pulse requirements: V GEN FIGURE 4. Timing test circuit and waveforms. (Address inputs to I/O) STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 ≤ ...
Page 14
NOTE: Input pulse requirements: V GEN FIGURE 5. Timing test circuit and waveforms. (Enable to I/O) STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 ≤ ...
Page 15
VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality ...
Page 16
MIL-STD-883 test requirements Interim electrical parameters (method 5004) Final electrical test parameters (method 5004) Group A test requirements (method 5005) Groups C and D end-point electrical parameters (method 5005) * PDA applies to subgroup 1. ** Subgroups 10 and 11, ...
Page 17
... The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the vendor to determine its availability. ...
Page 18
... Vendor name and address Maxim Integrated Products 120 San Gabriel Dr. Sunnyvale, CA 94086-5125 Analog Devices Rt 1 Industrial Park PO Box 9106 Norwood, MA 02062 Point of contact: (35361)495999 Raheen Business Park Limerick, Ireland Intersil Corporation 2401 Palm Bay Blvd PO Box 883 Melbourne, FL 32902-0883 ...